Yaskawa Z1000U User Manual
Page 372
oFC50 to oFC55 ................................................................ 199
OFF button Input ............................................................... 215
OFF Key ...........................................................................95
OFF Key Function Selection .................................................. 298
Offset Frequency................................................................ 316
oH ........................................................................... 199, 208
oH1 ............................................................................... 200
oH2 ............................................................................... 209
oH3 ......................................................................... 200, 209
oH4 ............................................................................... 200
oL1................................................................................ 200
oL1 Current Level .............................................................. 289
oL2................................................................................ 200
oL2 Characteristics Selection at Low Speeds......................... 171, 293
oL3.......................................................................... 200, 209
oL4................................................................................ 201
oL5................................................................................ 201
oPE ............................................................................... 211
oPE01 ............................................................................ 211
oPE02 ............................................................................ 211
oPE03 ............................................................................ 211
oPE05 ............................................................................ 212
oPE07 ............................................................................ 212
oPE08 ............................................................................ 212
oPE09 ............................................................................ 212
oPE10 ............................................................................ 213
oPE11 ............................................................................ 213
oPE16 ............................................................................ 213
oPE27 ............................................................................ 213
oPE28 ............................................................................ 213
oPE30 ............................................................................ 213
oPE Fault Parameter............................................................ 310
Open Loop Vector Control for PM Motors ...................................25
Open Loop Vector Control Mode Tuning Parameters ..................... 187
Operating with the Load Connected.......................................... 140
Operation Errors .......................................................... 189, 191
Operation Ready ..................................................................91
Operation Selection when HOA Keypad is Disconnected .......... 176, 298
Operation Status Monitors............................................... 180, 181
Operation with Permanent Magnet Motors.................................. 110
oPr ................................................................................ 201
Option card connection error (CN5-A) ...................................... 198
Option Card Connection Error at Option Port CN5-A..................... 198
Option Card Connection Error at Option Port CN5-C..................... 199
Option card error occurred at option port CN5-A .......................... 198
Option card error occurred at option port CN5-B .......................... 198
Option card error occurred at option port CN5-C .......................... 199
Option Card External Fault.............................................. 194, 206
Option Card Fault at Option Port CN5-A ................................... 198
Option Card Fault at Option Port CN5-B.................................... 198
Option Card Fault at Option Port CN5-C.................................... 199
Option Communication Error ........................................... 193, 204
Option Frequency Reference .................................................. 314
Option Installation .............................................................. 234
Option Monitors 1 to 20 ....................................................... 316
Oscillation or Hunting.......................................................... 225
Output Current .................................................................. 309
Output Current 1 during Speed Search ...................................... 147
Output Current at Previous Fault ............................................. 311
Output Current Imbalance ..................................................... 196
Output Frequency............................................................... 309
Output Frequency after Soft Start ............................................ 310
Output Frequency at Previous Fault.......................................... 311
Output Frequency Reduction During Overheat Alarm .................... 169
Output Frequency Resolution ................................................. 246
Output Ground Fault Detection Selection ............................. 170, 293
Output Phase Loss .............................................................. 196
Output Phase Loss Detection Level for Dynamic Audible Noise Control ...
Output Phase Loss Protection ................................................. 293
Output Phase Loss Protection Selection ..................................... 170
Output Power.................................................................... 309
Output Power at Previous Fault............................................... 311
Output Terminal Status ........................................................ 309
Output Terminal Status at Previous Fault ................................... 311
Output Voltage at Previous Fault ............................................. 311
Output Voltage Reference ..................................................... 309
Output Voltage Reference (Vd)............................................... 316
Output Voltage Reference (Vq)............................................... 316
ov............................................................................ 201, 209
Overcurrent ...................................................................... 197
Overcurrent Detection Gain ............................................. 171, 293
Overexcitation Deceleration Gain ............................................ 295
Overheat 1 (Heatsink Overheat) .............................................. 200
Overheat Alarm Level.................................................... 168, 293
Overheat Pre-Alarm Operation Selection ............................. 169, 293
Overload ......................................................................... 200
Overload Protection ............................................................ 246
Overtorque 1..................................................................... 209
Overtorque Detection 1 ........................................................ 200
Overtorque Detection 2 ........................................................ 201
Overvoltage Protection......................................................... 246
P
Parameter Access Level........................................................ 141
Parameter Range Setting Error................................................ 211
Parameter Selection Error ..................................................... 212
Parameter Settings .............................................................. 102
Parameters to Minimize Motor Hunting and Oscillation .................. 188
PASS ............................................................................. 209
Password ......................................................................... 141
Password Settings............................................................... 141
Peak Hold Current .............................................................. 314
Peak Hold Output Frequency ................................................. 314
Permanent Magnet Motor Control............................................ 110
Phase Order Detection Fault .................................................. 201
Phase Order Selection .......................................................... 145
PID Accel/Decel Time ......................................................... 151
PID Feedback ................................................................... 315
PID Feedback Function Selection ............................................ 153
PID Feedback High Detection Level......................................... 154
PID Feedback High Detection Time ......................................... 154
PID Feedback Loss Detection Selection..................................... 150
PID Feedback Low Detection Level ......................................... 151
PID Feedback Low Detection Time.......................................... 151
PID Feedback Offset ........................................................... 153
PID Function Setting ........................................................... 148
PID Input (feedback) ........................................................... 315
PID Input Limit ................................................................. 153
PID Maximum Boost Time.................................................... 153
PID Monitors .................................................................... 181
Index
372
YASKAWA ELECTRIC TOEP C710636 10B Z1000U HVAC MATRIX Drive User Manual