Yaskawa Z1000U - Manual (Page 285)

No.
(Addr.
Hex)
Name LCD Display Description Values Page
H3-11
(0419) Terminal A2 Gain
Setting
Terminal A2 Gain
Sets the level of the input value selected in H3-10 when 10 V
(20 mA) is input at terminal A2.
Default: 100.0%
Min.: -999.9
Max.: 999.9
125
H3-12
(041A) Terminal A2 Bias
Setting
Terminal A2 Bias
Sets the level of the input value selected in H3-10 when 0 V (0
or 4 mA) is input at terminal A2.
Default: 0.0%
Min.: -999.9
Max.: 999.9
125
H3-13
(041B)
Analog Input Filter Time
Constant
A1/A2 Filter T
Sets a primary delay filter time constant for terminals A1 and
A2. Used for noise filtering.
Default: 0.03 s
Min.: 0.00
Max.: 2.00
–
H3-14
(041C)
Analog Input Terminal
Enable Selection
A1/A2/A3 Sel
1: A1 Available
2: A2 Available
3: A1/A2 Available
4: A3 Available
5: A1/A3 Available
6: A2/A3 Available
7: All Available
Determines which analog input terminals will be enabled or
disabled when a digital input programmed for “Analog input
enable” (H1-oo = C) is activated.
The terminals not set as the target are not influenced by input
signals.
1: Terminal A1 only
2: Terminal A2 only
3: Terminals A1 and A2 only
4: Terminal A3 only
5: Terminals A1 and A3
6: Terminals A2 and A3
7: All terminals enabled
Default: 7
Range: 1 to 7
–
H3-16
(02F0)
Terminal A1 Offset TerminalA1Offset
Adds an offset when the analog signal to terminal A1 is at 0 V. Default: 0
Min.: -500
Max.: 500
–
H3-17
(02F1)
Terminal A2 Offset TerminalA2Offset
Adds an offset when the analog signal to terminal A2 is at 0 V. Default: 0
Min.: -500
Max.: 500
–
H3-18
(02F2)
Terminal A3 Offset TerminalA3Offset Adds an offset when the analog signal to terminal A3 is at 0 V.
Default: 0
Min.: -500
Max.: 500
–
<1> Default is 0 when b5-01 is set to 0.
Default is B when b5-01 is set to 1 or 3.
H3 Multi-Function Analog Input Settings
H3-oo
Setting
Function LCD Display Description Page
0 Frequency bias Freq Ref Bias 10 V = E1-04 (maximum output frequency) 164
1 Frequency gain Freq Ref Gain
0 to 10 V signal allows a setting of 0 to 100%. -10 to 0 V signal allows a setting
of -100 to 0%.
164
2
Auxiliary frequency
reference 1
(used as a Multi-Step
Speed 2)
Aux Reference1
10 V = E1-04 (maximum output frequency)
164
3
Auxiliary frequency
reference 2
(3rd step analog)
Aux Reference2
10 V = E1-04 (maximum output frequency)
164
4 Output voltage bias Voltage Bias 10 V = E1-05 (motor rated voltage) –
5 Accel/decel time gain Acc/Dec Change 10 V = 100% –
6
DC Injection Braking
current
DC Brake Current
10 V = Drive rated current
–
7
Overtorque/undertorque
detection level
Torque Det Level
10 V = Drive rated current (V/f)
10 V = Motor rated torque (OLV/PM)
–
8
Stall Prevention level
during run
Stall Prev Level
10 V = Drive rated current
–
9
Output frequency lower
limit level
Ref Lower Limit
10 V = E1-04 (maximum output frequency)
–
B PID feedback PID Feedback1 10 V = 100% 164
C PID setpoint PID Set Point 10 V = 100% 164
D Frequency bias Freq Ref Bias 2 10 V = E1-04 (maximum output frequency) 164
B.8 H Parameters: Multi-Function Terminals
YASKAWA ELECTRIC TOEP C710636 10B Z1000U HVAC MATRIX Drive User Manual 285
B
Parameter List