Altera CPRI IP Core User Manual
Page 114

6–16
Chapter 6: Signals
Physical Layer Signals
CPRI MegaCore Function
December 2013
Altera Corporation
User Guide
reconfig_fromgxb_s_rx
[16:0]
(
[4:0]
for
Cyclone IV GX devices)
Output
Driven to an external dynamic reconfiguration block from the slave receiver
transceiver block. The bus identifies the transceiver channel whose settings
are being transmitted to the dynamic reconfiguration block.
This signal is not present in Arria V, Cyclone V, and Stratix V variations.
reconfig_fromgxb_m
[16:0]
(
[4:0]
for
Cyclone IV GX devices)
Output
Driven to an external dynamic reconfiguration block from the master
transceiver block. The bus identifies the transceiver channel whose settings
are being transmitted to the dynamic reconfiguration block.
This signal is not present in Arria V, Cyclone V, and Stratix V variations.
reconfig_busy
Input
Indicates the busy status of the dynamic reconfiguration controller. After the
device powers up, this signal remains low for the first
reconfig_clk
clock
cycle. It is then asserted and remains high while the dynamic
reconfiguration controller performs offset cancellation on all the receiver
channels connected to the ALTGX_RECONFIG instance. This signal is
deasserted when offset cancellation completes successfully.
This signal is not present in Arria V, Cyclone V, and Stratix V variations.
reconfig_write
Input
Indicates the user is writing to the dynamic reconfiguration controller to
implement the autorate negotiation feature. Asserting this signal instructs
the CPRI reset controller to perform the reset sequence for dynamic
reconfiguration of the transceiver. For details about dynamic
reconfiguration, refer to the relevant device handbook.If you are not using
the autorate configuration feature, you must tie this input to 0.
This signal is not present in Arria V, Cyclone V, and Stratix V variations.
reconfig_done
Input
Indicates the dynamic reconfiguration controller has completed the
reconfiguration operation. Asserting this signal instructs the CPRI reset
controller to complete the reset sequence for dynamic reconfiguration of the
transceiver. For details about dynamic reconfiguration, refer to the relevant
device handbook. If you are not using the autorate negotiation feature, you
must tie this input to 0.
This signal is not present in Arria V, Cyclone V, and Stratix V variations.
gxb_pll_locked
Output
Indicates the transceiver transmitter PLL is locked to the input reference
clock. This signal is asynchronous.
gxb_rx_pll_locked
Output
Indicates the transceiver CDR is locked to the input reference clock. This
signal is asynchronous.
gxb_rx_freqlocked
Output
Transceiver clock data recovery (CDR) lock mode indicator. If this signal is
high, the transceiver CDR is in lock-to-data (LTD) mode. If this signal is low,
the transceiver CDR is in lock-to-reference clock (LTR) mode.
gxb_powerdown
Input
Transceiver block power down. This signal resets and powers down all
analog and digital circuitry in the transceiver block, including physical
coding sublayer (PCS), physical media attachment (PMA), clock multiplier
unit (CMU) channels, and central control unit (CCU). This signal does not
affect the
gxb_refclk
buffers and reference clock lines.
All the
gxb_powerdown
input signals of IP cores intended to be placed in
the same quad must be tied together. The
gxb_powerdown
signal must be
tied low or must remain asserted for at least 2 ms whenever it is asserted.
This signal is not present in ArriaV, Cyclone V, and Stratix V variations.
gxb_rx_disperr[1:0]
Output
Transceiver 8B/10B disparity error indicator. If either bit is high, a disparity
error was detected on the associated received code group.
Table 6–14. Transceiver Signals (Part 2 of 3)
Signal Direction
Description