Rockwell Automation DAG6.5.8 APPLICATION GUIDE SCADA SYSTEM - Manual (Page 415)

Publication AG-UM008C-EN-P - February 2005
Index 5
Getting MicroLogix 1000 processors to
accept byte offsets 6-17
MSG
configuration considerations 6-16
polled report-by-exception 6-15
Micrologix
messaging
processor-to-processor 6-15
MicroLogix 1100/1200/1500 3-2, 3-42
Active stations, monitoring 3-18
Channel Status 3-17
Configuring
Channel 0 Poll Timeout 3-25
DF1 Half-Duplex 3-11
DF1 Half-Duplex Master
Message-based 3-19
Standard Mode 3-12
Minimum Channel 0 ACK Timeout
3-14
Minimum Point-to-Point MSG Block
Message Timeout 3-41
Minimum Slave MSG Block Mes-
sage Timeout 3-40
Point-to-Point 3-33
RTS Off Delay 3-11
RTS Send Delay 3-11
Slave Station 3-22
DF1 Full-Duplex
Channel Status 3-30, 3-35
Installing 3-2
Message
configuration considerations 3-37
Messaging 3-36
Examples 3-42
Master Station to Slave Station
3-36
Message-based Polling Mode 3-38
Minimum Master MSG Block Mes-
sage Timeout 3-38
Polled Report-by-Exception 3-36
Processor-to-Processor 3-37
Standard Polling Mode 3-39
Modems 3-6
Control Line Operation 3-8
DF1 Full-Duplex 3-8
DF1 Half-Duplex Master 3-9
DF1 Half-Duplex Slave 3-8
Dial-up 3-6
Full-Duplex 3-8
handshaking 3-8
Leased-Line 3-7
Line Drivers 3-7
Radio 3-7
Overview 3-2
MicroLogix Controllers 6-1
Installing 6-3
Isolated Connections 6-4
Overview 6-2
Modbus RTU protocol 3-46
Modem
definition Glossary-3
dialing 10-5
Modem handshaking
definition Glossary-3
Modems 8-1
Configuration 8-2
Telephone Modems 8-2
Installing 8-1
Power Line Modems 8-39
Radio Modems 8-21, 8-23, 8-29,
8-35
Telephone Modems 8-5, 8-11
using dial-up 10-1
MSG
Micrologix 1000 read to MicroLogix, SLC
500 or Logix 6-22
MicroLogix 1000 read to PLC-5 6-20
MicroLogix 1000 write to MicroLogix,
SLC 500, or Logix 6-21
MicroLogix 1000 write to PLC-5 6-19
MicroLogix 1100/1200/1500 controller to
a PLC-5 processor or Logix
controller
3-42, 3-43
MicroLogix 1100/1200/1500 controller to
an SLC 500 or MicroLogix
Controller
3-44
MicroLogix 1100/1200/1500 controller to
an SLC 500 or MicroLogix
controller
3-45
SLC 5/01 and 5/02 read to SLC 500 5-17
SLC 5/01 and 5/02 write to SLC 500 5-16
SLC 5/02 read to PLC-5 5-15
SLC 5/02 write to PLC-5 5-14
SLC 5/03, 5/04 or 5/05 read to a PLC-5
processor or Logix controller
4-44
SLC 5/03, 5/04 or 5/05 read to another
SLC 500 or MicroLogix
controller
4-46
SLC 5/03, 5/04 or 5/05 write to a PLC-5
processor or Logix controller
4-43
SLC 5/03, 5/04 or 5/05 write to another
SLC 500 or MicroLogix
controller
4-45
MSG considerations