Yaskawa L1000E AC Drive CIMR-LE†A - Manual (Page 214)

B Parameter Table
214 YASKAWA TOEPYAIL1E01A YASKAWA AC Drive L1000E Quick Start Guide
U4-21
(7DDH)
Up/Down Command
Source Selection
Displays the source for the Up/Down command as XY-nn.
X: Indicates which Up/Down command source is used:
1 = Reference 1 (b1-02)
Y: Input power supply data
0 = Digital operator
1 = External terminals
3 = MEMOBUS/Modbus communications
4 = Communication option card
nn: Up/Down command limit status data
00: No limit status.
01: Up/Down command was left on when stopped in the PRG mode
02: Up/Down command was left on when switching from LOCAL to
REMOTE operation
03: Waiting for soft charge bypass contactor after power up (Uv or Uv1 flashes
after 10 s)
04: Waiting for "Up/Down Command Prohibited" time period to end
05: Fast Stop (multi-function input, operator)
07: During baseblock while coast to stop with timer
08: Speed reference is below minimal reference during baseblock
09: Waiting for Enter command
No signal output
available
–
U4-22
(7DEH)
MEMOBUS/Modbus
Communications
Reference
Displays the drive control data set by MEMOBUS/Modbus communications
register no. 0001H as a four-digit hexadecimal number.
No signal output
available
–
U4-23
(7DFH)
Communication Option
Card Reference
Displays drive control data set by an option card as a four-digit hexadecimal
number.
No signal output
available
–
U4-24
(7E6H)
Number of Travels
(Lower 4 digit)
Displays the lower four digits for the number of trips the drive has made.
No signal output
available
1 time
U4-25
(7E7H)
Number of Travels
(Higher 4 digit)
Displays the upper four digits for the number of trips the drive has made.
No signal output
available
1 time
U4-26
(7E8H)
Max. Current during
Acceleration
Shows the maximum current that occurred during acceleration.
No signal output
available
0.1 A
U4-27
(7E9H)
Max. Current during
Deceleration
Shows the maximum current that occurred during deceleration.
No signal output
available
0.1 A
U4-28
(7EAH)
Max. Current during
Constant Speed
Shows the maximum current that occurred during ride at top speed.
No signal output
available
0.1 A
U4-29
(7EDH)
Max. Current during
Leveling Speed
Shows the maximum current that occurred during ride at leveling speed.
No signal output
available
0.1 A
U4-30
(7EEH)
Slip Compensation Value
Shows the slip compensation value.
No signal output
available
0.01%
U4-31
(7EFH)
Car Acceleration Rate
Shows the car acceleration rate.
No signal output
available 0.01 m/
s 2
U4-40
(7FDH)
Speed Reference Limit at
Rescue Operation
Displays the speed limit for Rescue Operation based on how much power the
backup battery or UPS has. Displays 0% when Rescue Operation is not being
performed.
No signal output
available
1%
U4-42
(855H)
<35>
Remaining Distance
Displays the remaining distance according to the stopping method selected.
10 V:
S5-10 = 1: S5-11
S5-10 = 2: S5-12
1 mm
No.
(Addr.)
Name Description
Analog Output
Level
Unit
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
common
_ CLV CLV/PM V/f OLV
common
_ CLV CLV/PM V/f OLV
All Modes
common
_
CLV CLV/PM V/f OLV
common
_