Comtech EF Data CDM-760 - Manual (Page 251)

Serial-based Remote Product Management Revision 2
CDM-760 Advanced High-Speed Trunking Modem MN-CDM760
8–17
8.5.4 IP Packet Parameters
Parameter
Type
Command
(Instruction
& Qualifier)
Number of
Arguments
Description of Arguments
Response to
Command
Query
(Instruction &
Qualifier)
Response to Query
Payload
Compression
EPC = 1 byte, value
of 0 thru 3
Command or Query.
Enable or Disable Payload Compression and Decompression in the form x, where:
0 = Disable Decompression, Disable Compression
1 = Disable Decompression, Enable Compression
2 = Enable Decompression, Disable Compression
3 = Enable Decompression, Enable Compression
EXAMPLE: <0/EPC = 1 (selects decompression off and compression on)
EPC=
EPC?
EPC*
EPC#
EPC? EPC=x
(see Description of
Arguments)
Compression
Stats All
N/A 21 bytes Query only.
Returns all compression statistics, each separated by a colon, in the form x.xE+xx:x.xE+xx:xx:xx, where:
x.xE+xx = The total number of bytes into the compressor
x.xE+xx = The total number of bytes out of the compressor
xx = value from 00 to 99 (The percent savings or compression efficiency)
xx = value from 00 to 99 (The last 10 seconds percent savings or compression efficiency)
EXAMPLE: <0/CSA?
RESPONSE EXAMPLE 1: >0000/CSA=2.0E+03:1.0E+03:50:50
RESPONSE EXAMPLE 2: >0000/CSA=X.XE+XX:X.XE+XX:XX:XX (If the Compression Option Card is not
present, then all numeric fields display "X")
N/A CSA? CSA=
x.xE+xx:x.xE+xx:xx:
xx
DeComp
Stats All
N/A 21 bytes Query only.
Returns all decompression statistics, each separated by a colon, in the form x.xE+xx:x.xE+xx:xx:xx, where:
x.xE+xx = The total number of bytes into the decompressor
x.xE+xx = The total number of bytes out of the decompressor
xx = value from 00 to 99 The percent savings or decompression efficiency
xx = value from 00 to 99 The last 10 second percent savings or decompression efficiency
EXAMPLE: <0/ESA?
RESPONSE EXAMPLE 1: <0/DSA=2.0E+03:1.0E+03:50:50
RESPONSE EXAMPLE 2: <0/DSA=X.XE+XX:X.XE+XX:XX:XX (if the Decompression Option Card is not
present, then all numeric fields display "X")
N/A DSA? DSA=x.xE+xx:x.xE+
xx:xx:xx
Clear
Compression
Statistics
CCS = None Command only.
Clear Compression Statistics.
NOTE: THIS COMMAND TAKES NO ARGUMENTS.
EXAMPLE: <0/CCS=
CCS=
CCS?
CCS*
CCS#
N/A N/A
Clear De-
compression
Statistics
CDS = None Command Only.
Clear Decompression Statistics.
NOTE: THIS COMMAND TAKES NO ARGUMENTS.
EXAMPLE: <0/CDS=
CDS=
CDS?
CDS*
CDS#
N/A N/A
WAN Buffer
Length
WBL 3 bytes Command or Query.
Sets or returns WAN Buffer Length in ms, in 20 ms steps, in the form xxx where:
xxx = value from 20 to 400ms
EXAMPLE: <0/WBL=100
WBL=
WBL?
WBL*
WBL#
WBL? WBL=xxx
(see Description of
Arguments)