Rockwell Automation 1771-QDC PLASTIC MOLD.MODULE - Manual (Page 11)

Table of Contents ix
Clamp Open Slow Profile Actuals 3–19 . . . . . . . . . . . . . . . . . .
Open Profile Maximum Pressures 3–19 . . . . . . . . . . . . . . . . . .
Open Profile Execution Times 3–20 . . . . . . . . . . . . . . . . . . . . .
PPS – Plastication Profile Status Block 3–20 . . . . . . . . . . . . . . . .
Bit-mapped Status Words 3–20 . . . . . . . . . . . . . . . . . . . . . . . .
Plastication Profile Actuals 3–21 . . . . . . . . . . . . . . . . . . . . . . .
Plastication Maximum Pressure 3–22 . . . . . . . . . . . . . . . . . . .
Post-decompression Maximum Pressure 3–22 . . . . . . . . . . . . .
Execution Times 3–22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Post-decompression Movement Actuals 3–22 . . . . . . . . . . . . .
Shot Size Actual 3–22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PTS – Process Trace Status Block 3–22 . . . . . . . . . . . . . . . . . . .
Bit-mapped Status Words 3–22 . . . . . . . . . . . . . . . . . . . . . . . .
RLS – Inject ERC Values Status Block 3–24 . . . . . . . . . . . . . . . . .
Bit-mapped Status Words 3–24 . . . . . . . . . . . . . . . . . . . . . . . .
Injection Profile ERC Actuals 3–24 . . . . . . . . . . . . . . . . . . . . .
Pack Profile ERC Actuals 3–24 . . . . . . . . . . . . . . . . . . . . . . . .
Hold Profile ERC Actuals 3–25 . . . . . . . . . . . . . . . . . . . . . . . .
Plastication Profile ERC Actuals 3–25 . . . . . . . . . . . . . . . . . . .
SYS – System Status Block 3–25 . . . . . . . . . . . . . . . . . . . . . . . .
Input Level In Engineering Units 3–46 . . . . . . . . . . . . . . . . . . .
Input Level, Raw Signal 3–46 . . . . . . . . . . . . . . . . . . . . . . . . .
Output Level in Percentage 3–46 . . . . . . . . . . . . . . . . . . . . . .
Cycle Maximum Pressures 3–47 . . . . . . . . . . . . . . . . . . . . . . .
Process Trace Data Collection Status 3–47 . . . . . . . . . . . . . . .
Process Times 3–48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostics 3–48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
New Status Confirmation 3–48 . . . . . . . . . . . . . . . . . . . . . . . .
Programming Error Codes 4–1 . . . . . . . . . . . . . . . . . . . . .
How to Read Error Codes 4–2 . . . . . . . . . . . . . . . . . . . . . . . . . .
ID = 1 – MCC – Module Configuration Command Block 4–3 . . . .
ID = 2 – JGC – Jog Configuration Block 4–6 . . . . . . . . . . . . . . . .
ID = 3 – FCC – First Clamp Close Configuration Block 4–7 . . . . .
ID = 4 – SCC – Second Clamp Close Configuration Block 4–9 . . .
ID = 5 – TCC – Third Clamp Close Configuration Block 4–10 . . . . .
ID = 6 – LPC – Clamp Low Pressure Close Configuration Block 4–11
ID = 7 – CPC – Clamp Close Profile Block 4–12 . . . . . . . . . . . . . .
ID = 8 – INC – Injection Configuration Block 4–17 . . . . . . . . . . . . .
ID = 9 – IPC – Injection Profile Block 4–18 . . . . . . . . . . . . . . . . . .
ID = 10 – PKC – Pack Configuration Block 4–25 . . . . . . . . . . . . . .
ID = 11 – HDC – Hold Configuration Block 4–26 . . . . . . . . . . . . . .
ID = 12 – HPC – Pack/Hold Profile Block 4–28 . . . . . . . . . . . . . . .
ID = 13 – PRC – Pre-Decompression Configuration Block 4–30 . . .
ID = 14 – PLC – Plastication Configuration Block 4–31 . . . . . . . . .