Rockwell Automation 20D PowerFlex 700S AC Drives with Phase II Control Programming Manual User Manual
Page 91
Rockwell Automation Publication 20D-PM001C-EN-P - July 2013
91
Programming and Parameters
Chapter 2
514 Test
Mode
Config
Configures the Motor Control (MC) test mode.
Note: This parameter was changed to non-linkable for firmware version 3.001.
515
FVC Tune Config
Configures FOC tuning mode.
• Bit 1 “FluxCurrTune” when set, the value in
[Flux Current] is used as the flux current at the beginning of the magnetic inductance test. When this bit is not set (default), an automatically
calculated (preset) flux current is used as the flux current at the beginning of the magnetic inductance test.
• Bit 2 “NoTimeLimit” when set, the time limit fault detection during the magnetizing inductance test is disabled.
Note: Bits 1 and 2 were added for firmware version 4.001.
516
FVC2 Tune Config
Configures FOC 2 tuning mode.
No.
Name
Description
Values
Link
able
Re
ad
-Write
Da
ta
T
yp
e
ATTENTION: Do not modify this parameter. Motor/Drive instabilities and damage may result.
Options
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
flW
av
e C
omp
Bus
Gai
n C
om
p
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Default
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
1
1
x
x
x
x
x
x
x
x
Bit
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
0 = False
1 = True
ATTENTION: Do not modify this parameter. Motor/Drive instabilities and damage may result.
Options
Res
er
ve
d
Res
er
ve
d
Res
er
ve
d
Res
er
ve
d
Res
er
ve
d
Res
er
ve
d
No
Ro
ta
te
Tu
ne
Res
er
ve
d
Res
er
ve
d
Res
er
ve
d
Res
er
ve
d
Res
er
ve
d
Res
er
ve
d
No
Tim
eL
imi
t
Fl
ux
Cu
rr
Tu
ne
Res
er
ve
d
Default
x
x
x
x
x
x
0
x
x
x
x
x
x
0
0
x
Bit
15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
0 = False
1 = True
ATTENTION: Do not modify this parameter. Motor/Drive instabilities and damage may result.
Options
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
N
oRo
tate
Tu
ne
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Default
x
x
x
x
x
x
0
x
x
x
x
x
x
x
x
x
Bit
15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
0 = False
1 = True