Par 511 – Rockwell Automation 20D PowerFlex 700S AC Drives with Phase II Control Programming Manual User Manual
Page 90
90
Rockwell Automation Publication 20D-PM001C-EN-P - July 2013
Chapter 2
Programming and Parameters
511 FVC2
Mode
Config
Configures Field Oriented Control - 2 (FOC2) operation.
Notes: Bit changes were made for firmware version 2.003. This parameter was changed to non-linkable for firmware version 3.001.
512
PMag Mode Config
Configures Permanent Magnet (PM) operation.
• Bit 0 “PM Cogging” when set, enables torque ripple compensation.
• Bit 9 “ReflWaveComp” when set, Reflected Wave Correction is enabled.
Notes: Bit changes were made for firmware version 2.003. This parameter was changed to non-linkable for firmware version 3.001. Added bit 9 for firmware version 4.001. Bit 0 “PM Cogging” was
added for firmware version 5.002.
513
V/Hz Mode Config
Configures V/Hz control mode operation.
Notes: This parameter was added for firmware version 2.003. Changed bit 3 from “Reserved” to “FastFluxDsbl” for firmware version 3.003. Bits 8, 9, and 21 were changed to be not changeable while
the drive is running.
No.
Name
Description
Values
Link
able
Re
ad
-Write
Da
ta
T
yp
e
ATTENTION: Do not modify this parameter. Motor/Drive instabilities and damage may result.
Options
LnfS
ns
r Dir
LnfS
ns
r U
se
Re
se
rv
ed
Flx
Rat
Rf
Use
NT
C A
ctiv
e
Re
se
rv
ed
Re
se
rv
ed
CEMF W
e U
se
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Bus
Gai
n C
omp
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Default
0
0
x
0
1
x
x
0
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
1
x
x
x
x
x
x
x
x
Bit
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
0 = False
1 = True
ATTENTION: Do not modify this parameter. Motor/Drive instabilities and damage may result.
Options
LinrSnsr Di
r
LinrSnsr U
se
Re
se
rv
ed
Flx
RatR
f Us
e
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
CEMF W
e
U
se
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
PM
VltRegU
se
PM
Vl
tR
eg
En
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
flW
av
eC
omp
BusGa
in C
om
p
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
PM
C
ogging
Default
0
0
x
0
x
x
x
0
x
x
x
x
1
1
x
x
x
x
x
x
x
x
1
1
x
x
x
x
x
x
x
0
Bit
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
0 = False
1 = True
ATTENTION: Do not modify this parameter. Motor/Drive instabilities and damage may result.
Options
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Vl
tM
in
or
Lp
En
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
flW
av
eC
omp
BusGai
n C
om
p
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Fa
st
Fl
ux
Ds
bl
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Default
x
x
x
x
x
x
x
x
x
x
1
x
x
x
x
x
x
x
x
x
x
x
1
1
x
x
x
x
1
x
x
x
Bit
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
0 = False
1 = True