Teledyne 9110E - Nitrogen Oxides Analyzer - Manual (Page 4)

M9110E Documentation Model 9110E Instruction Manual
iv M9110E Rev B
5.10. Additional Manual (Option 70) ......................................................................................43
5.11. Manual on CD (Option 70A)................................................Error! Bookmark not defined.
5.12. Extended Warranty (Options 92 & 93) ...........................................................................43
6. OPERATING INSTRUCTIONS ........................................................................................... 45
6.1. Overview of Operating Modes.........................................................................................45
6.2. Sample Mode ...............................................................................................................46
6.2.1. Test Functions .......................................................................................................46
6.2.2. Warning Messages..................................................................................................48
6.2.3. Calibration Functions ..............................................................................................48
6.3. Calibration Mode...........................................................................................................49
6.4. Setup Mode..................................................................................................................49
6.4.1. Password (PASS)....................................................................................................49
6.4.2. Configuration Information (CFG) ..............................................................................51
6.4.3. Clock (CLK) ...........................................................................................................51
6.5. Setup - Range Configuration (RNGE)...............................................................................52
6.5.1. Physical and Analog Output Ranges ..........................................................................53
6.5.2. Reporting Range Modes ..........................................................................................53
6.5.3. Single Range mode (SNGL) .....................................................................................54
6.5.4. Independent Range Mode (IND) ...............................................................................54
6.5.5. Auto Range Mode (AUTO)........................................................................................56
6.5.6. Range Units...........................................................................................................56
6.5.7. Dilution Ratio.........................................................................................................57
6.6. Setup - Internal Variables (VARS)...................................................................................59
6.7. Setup - Diagnostics (DIAG) ............................................................................................61
6.7.1. Signal I/O .............................................................................................................62
6.7.2. Analog Output Step Test .........................................................................................63
6.7.3. Analog I/O Configuration.........................................................................................64
6.7.3.1. Analog Output Signal Type and Range Selection ..................................................65
6.7.3.2. Analog Output Calibration Mode.........................................................................66
6.7.3.3. Manual Analog Output Calibration ......................................................................68
6.7.3.4. Analog Output Offset Adjustment.......................................................................69
6.7.3.5. Current Loop Output Adjustment .......................................................................70
6.7.3.6. AIN Calibration ................................................................................................72
6.7.4. Test Channel Output...............................................................................................72
6.7.5. Optic Test .............................................................................................................74
6.7.6. Electrical Test ........................................................................................................74
6.7.7. Ozone Generator Override.......................................................................................75
6.7.8. Flow Calibration .....................................................................................................76
6.8. Digital Inputs and Outputs .............................................................................................76
6.8.1. Status Outputs.......................................................................................................76
6.8.2. Control Inputs........................................................................................................77
6.9. Setup - Communication Ports (COMM).............................................................................78
6.9.1. Analyzer ID ...........................................................................................................79
6.9.2. COM Port Default Settings .......................................................................................79
6.9.3. COM Port Cable Connections....................................................................................80
6.9.4. COM2 Configuration................................................................................................80
6.9.5. DTE and DCE Communication ..................................................................................81
6.9.6. COM Port Communication Modes ..............................................................................81
6.9.7. COM Port Baud Rate ...............................................................................................84
6.9.8. COM Port Testing ...................................................................................................84
6.9.9. Ethernet Port Configuration .....................................................................................85
6.9.10. Hessen Mode Configuration....................................................................................88
6.10. Setup - Data Acquisition System (DAS) .........................................................................89
6.10.1. iDAS Structure .....................................................................................................90
6.10.1.1. iDAS Channels ...............................................................................................90
6.10.1.2. iDAS Parameters............................................................................................91
6.10.1.3. iDAS Triggering Events ...................................................................................92
6.10.2. Configuring the iDAS.............................................................................................92
6.10.2.1. Default M9110E iDAS Configuration..................................................................92
6.10.2.2. Viewing iDAS Data and Settings.......................................................................94