Ag Leader EDGE Ver.4.5 Users Manual Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for EDGE Ver.4.5 Users Manual Ag Leader
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 214 |
| Size: | 2.79 MB |
Show table of contents
Document Outline
- General
- Setup
- GPS
- Guidance
- GPS Guidance Tab
- Guidance Functions
- SmartPathNotes:
- OnTrac2
- Tillage
- Planting
- Run Time Environment: Map Screen
- Planting Setup Tabs
- Create a Planting Configuration
- Configuration Settings
- Vehicle Tab
- Implement Tab
- Controller Tab
- Product Tab
- Planting: SeedCommand™ Machine-Specific Setup
- Run Time Environment: Rate Screen
- Row Shutoff
- Hydraulic Seed Rate Control
- Stepper Seed Rate Control
- Stepper Seed Rate Control Configuration
- Controller Settings for Stepper Seed Rate Motor Drives
- Channel Tabs
- Auxiliary Tab
- Gear Ratio Calculations for Seed Rate Motors
- Gear Ratio Drawing - For Single Motor Drive
- Gear Ratio Drawing - For Multiple Drive Combinations
- Seed Ratio Calculation Example Procedure
- Gear Ratio Drawing - For John Deere Pro-Shaft™ Drives
- Priming Seed Rate Meters
- Calibrating Seed Rate Meters
- Troubleshooting
- Zero Flow Offset Variation
- a. Turn the Master Switch off. Enter a manual ground speed and enter a new region.
- b. From the Run screen, open the product application rate window, and highlight the appropriate product. Select Manual control mode.
- c. Switch the Master Switch on.
- d. Press the up button one time. Now press the down button one time. If the drive is not turning, the Zero Flow Offset is likely to be too low.
- a. Turn the Master Switch off. Enter a manual ground speed and create a new region.
- b. Increase Zero Flow Offset by 2.
- c. From the Run screen, open the product application rate window, and highlight the appropriate product. Select Manual control mode.
- d. Switch the Master Switch on.
- e. Press the up button one time. Now press the down button one time. The drive should be turning. If not, repeat this procedure starting with Step 2.
- Hydraulic Seed Control: Zero Flow Offset Variation
- a. Turn the Master Switch off. Enter a manual ground speed and create a new region.
- b. From the Run screen, open the product application rate window, and highlight the appropriate product. Select Manual control mode.
- c. Switch the Master Switch on.
- d. Press the up button one time. Now press the down button three times. If the drive is still turning, the zero flow offset is likely to be too high.
- a. Turn the Master Switch off. Enter a manual ground speed and enter a new region.
- b. Reduce Zero Flow Offset by 2.
- c. From the Run screen, open the product application rate window, and highlight the appropriate product. Select Manual control mode.
- d. Switch the Master Switch on.
- e. Press the up button one time. Now press the down button three times. The drive should not be turning. If it is, repeat this procedure, starting with step 2.
- Stepper Seed Control Meter Alarms
- Zero Flow Offset Variation
- Diagnostics
- Application
- Run Time Environment: Map Screen
- Application Setup Tabs
- Create an Application Configuration
- Configuration Settings
- Vehicle Tab
- Implement Tab
- Controller Tab
- Product Tab
- Miscellaneous Items
- MASTER SWITCH INPUT
- MASTER SWITCH USAGE
- TARGET RATE
- DATA COLLECTION
- AUTOSWATH BOOM SECTION CONTROL
- SPRAY STAR APPLICATION RATE
- SPRAY STAR RINSE CYCLE
- Control Valve Settings
- Liquid Product Control Valve Configuration
- Servo Control Valve Settings (By Manufacturer)
- Control Valve Settings for Self-Propelled Sprayers
- Liquid Servo Settings Description
- Liquid PWM Control Valve Settings Description
- Spinner Spreader Servo Settings Description
- Spinner Spreader PWM Control Valve Settings Description
- Spinner Speed PWM Valve Settings Description
- Dickey John NH3 Conversions
- Application: DirectCommand™ Machine- Specific Setup
- Map Screen: Zoom to Extent
- Map Screen: Zoom Detail
- Run Time Environment: Rate Screen
- Shape File Conversion
- Liquid Application Control
- Direct Injection
- Spinner Spreader Granular Control
- NORAC UC5 Setup
- Troubleshooting
- Battery Power Pin-Outs
- Discharge Flow Sensor Pin Outs
- VACUUM SWITCH PIN OUTS
- Miscellaneous
- Diagnostics
- Harvest
- Appendix