Contents i – Lenze E82xVxxxKxxxxx User Manual
Page 12

Contents
i
l
12
EDS82EV903 EN 3.0
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Monitoring the safety function with a PLC
. . . . . . . . . . . . . . . . . . . . . . . .
Example 1: Simple pressure control with fixed setpoint selection
Example 2: Simple pressure control with changeable setpoint selection
15.2 Operation with mid−frequency motors
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.4 Group drive (operation with several motors)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.5 Setpoint summation (basic and additional load operation)
. . . . . . . . . . . . . . . . . .
15.6 Power control (torque limitation)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.2 Signal processing − overview
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller with Standard I/O and communication module
Controller with application I/O
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller with Application I/O and communication module
Controller with communication module
. . . . . . . . . . . . . . . . . . . . . . . . . .
Controller with fieldbus function module
. . . . . . . . . . . . . . . . . . . . . . . . .
Controller with fieldbus function module and communication module
Controller with system bus function module
. . . . . . . . . . . . . . . . . . . . . .
Controller with system bus function module and
communication module
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.3 Signal processing in the function blocks
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speed setpoint conditioning (NSET1)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speed setpoint conditioning (NSET1) with Application I/O
Process controller and setpoint processing (PCTRL1)
. . . . . . . . . . . . . . . .
Process controller and setpoint processing (PCTRL1)
with Application I/O
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor control (MCTRL1) with Application I/O
. . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller state (STAT1, STAT2)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Process data of system bus function module (CAN1, CAN2)
16.3.10 Process data of fieldbus function module (FIF−IN, FIF−OUT)