Comtech EF Data C5 User Manual
Page 304
Remote Control Operation
C5/K1/K3 Integrated Satellite Terminal System
B–20
Rev. 0
Interface
Configuration
Status
Command:
Response:
TC_xxx'cr'
ERF_nnnnn.n'cr'
TCP_xxxx'cr'
RCP_xxxx'cr'
BBL_xxx'cr'
ILB_xxx'cr'
ILT_xxx'cr'
ICFT_xxxx'cr'
ICFR_xxxx'cr'
BC_xxx'cr'
IRFS_T1_ssss'cr'
IRFS_E1_ssss'cr'
IBP_xxx'cr'
IBS_nnnnnn'cr'
ITOT_xxxxx'cr'
IROT_xxxxx'cr'
ISP_xxx'cr'
IRE_xxxx'cr'
TDF_xxxx'cr'
RDF_xxxx'cr'
TDP_xxxx'cr'
RDP_xxxx'cr'
TXDR_xxxxxx'cr'
RXDR_xxxxxx'cr'
TOBR_nnnnn'cr'
(Note 1)
TCCL_n'cr'
(Note 1)
TCSB_n'cr'
(Note 1)
TOCP_xxxx'cr'
(Note 1)
TCT_xxxxx'cr'
(Note 1)
ROBR_nnnnn'cr'
(Note 2)
RCCL_n'cr'
(Note 2)
RCSB_n'cr'
(Note 2)
ROCP_xxxx'cr'
(Note 2)
RCT_xxxxx'cr'
(Note 2)
LPC_xxx'cr'
(Note 1)
NOMP_snn.n'cr'
(Note 1)
MINP_snn.n'cr'
(Note 1)
MAXP_snn.n'cr'
(Note 1)
LCL_xxxx'cr'
(Note 1)
RCL_xxxx'cr'
(Note 1)
ENSP_nn.n'cr'
(Note 2)
MAXT_n.n'cr'
(Note 2)
RTSM_xxx'cr'
CTSD_xx'cr''lf']
Transmit Clock (Source)
External Reference Frequency
Transmit Clock Phase
Receive Clock Phase
Base Band Loopback
Interface Loopback
Interface Loop Timing
Interface Coding Format Transmit
Interface Coding Format Receive
Buffer Clock (Source)
Interface Receive Frame Structure (T1)
Interface Receive Frame Structure (E1)
Interface Buffer Programming
Interface Buffer Size
Interface Transmit Overhead Type
Interface Receive Overhead Type
Interface Substitution Pattern (TX 2047)
Interface Read Error (RX 2047)
Transmit Data Fault
Receive Data Fault
Transmit Data Phase
Receive Data Phase
TX Driver Type
RX Driver Type
ASYNC Transmit Overhead Baud Rate
ASYNC Transmit Channel Character Length
ASYNC Transmit Channel Stop Bits
ASYNC Transmit Overhead Channel Parity
ASYNC Transmit Communications Type
ASYNC Receive Overhead Baud Rate
ASYNC Receive Channel Character Length
ASYNC Receive Channel Stop Bits
ASYNC Receive Overhead Channel Parity
ASYNC Receive Communications Type
AUPC Local Power Enable
AUPC Nominal Power Value
AUPC Minimum Power Value
AUPC Maximum Power Value
AUPC Local Carrier Loss
AUPC Remote Carrier Loss
AUPC EBN0 Target Set Point
AUPC Maximum Tracking Rate
RTS TX-IF Control Mode
CTS Delay Time
The Interface configuration status command causes a block
of data to be returned by the addressed MODEM. The block
reflects the current configuration of the interface. Additional
configuration status of new options and features will always
be appended to the end.
Notes:
1. Data is only returned for TX ASYNC Overhead.
2. Data is only returned for RX ASYNC Overhead.