Teledyne GFC-7000E - Trace CO2 Analyzer - Manual (Page 8)

Model GFC7000E Instruction Manual GFC7000E Documentation
04584 Rev A1 vii
LIST OF APPENDICES
APPENDIX A - VERSION SPECIFIC SOFTWARE DOCUMENTATION
APPENDIX A-1: MGFC7000E Software Menu Trees, Revision E.0
APPENDIX A-2: Setup Variables For Serial I/O, Revision E.0
APPENDIX A-3: Warnings and Test Functions, Revision E.0
APPENDIX A-4: MGFC7000E Signal I/O Definitions, Revision E.0
APPENDIX A-5: MGFC7000E iDAS Functions, Revision E.0
APPENDIX A-6: Terminal Command Designators, Revision E.0
APPENDIX B - GFC7000E SPARE PARTS LIST
APPENDIX C - REPAIR QUESTIONNAIRE - MGFC7000E
APPENDIX D - ELECTRONIC SCHEMATICS
LIST OF FIGURES
Figure 3-1: Removal of Shipping Screws.......................................................................... 10
Figure 3-2: Rear Panel Layout ........................................................................................ 12
Figure 3-3: Pneumatic Connections–Basic Configuration–Using Bottled Span Gas .................. 16
Figure 3-4: Pneumatic Connections–Basic Configuration–Using Gas Dilution Calibrator ........... 17
Figure 3-5: Pneumatic Connections–MGFC7000E with Zero/Span/Shutoff Valves (OPT 50)...... 19
Figure 3-6 Pneumatic Connections–MGFC7000E with Zero/Span/Shutoff Valves and External
Zero Air Scrubber (OPT 51).......................................................................... 19
Figure 3-7: Pneumatic Connections–MGFC7000E with Zero/Span Valves (OPT 52) ................. 20
Figure 3-8: Pneumatic Connections–MGFC7000E with Zero/Span Valves with External Zero air
Scrubber (OPT 53)...................................................................................... 20
Figure 3-9: Example of Pneumatic Set up for Multipoint Calibration of M360 ......................... 21
Figure 3-10: Front Panel Layout ....................................................................................... 23
Figure 3-11: Assembly Layout.......................................................................................... 30
Figure 3-12: Optical Bench Layout .................................................................................... 31
Figure 3-13: Internal Pneumatic Flow – Basic Configuration ................................................. 31
Figure 5-1: Current Loop Option Installed on the Motherboard ............................................ 37
Figure 5-2: Internal Pneumatic Flow – Zero/Span/Shutoff Valves OPT 50 & 51 ...................... 39
Figure 5-3: Internal Pneumatic Flow – Zero/Span OPT 52 & 53 ........................................... 41
Figure 5-4: GFC7000E Ethernet Card and rear panel With Ethernet Installed......................... 42
Figure 6-1: Front Panel Display ...................................................................................... 45
Figure 6-2 Viewing MGFC7000E TEST Functions ............................................................... 48
Figure 6-3 Viewing and Clearing MGFC7000E WARNING Messages...................................... 50
Figure 6-4: Analog Output Connector Pin Out ................................................................... 56
Figure 6-5: Setup for Calibrating Analog Voltage Outputs................................................... 74
Figure 6-6: Setup for Calibrating Current Outputs ............................................................. 75
Figure 6-7: Default iDAS Channels Setup....................................................................... 101
Figure 6-8: APICOM user interface for configuring the iDAS. ............................................. 113
Figure 6-9: iDAS Configuration Through a Terminal Emulation Program.............................. 114
Figure 6-10: Status Output Connector............................................................................. 115
Figure 6-11: Control Inputs ........................................................................................... 117
Figure 6-12: APICOM Remote Control Program Interface.................................................... 123
Figure 7-1: Pneumatic Connections–Basic Configuration–Using Bottled Span Gas ................ 130
Figure 7-2: Pneumatic Connections–Basic Configuration–Using Gas Dilution Calibrator ......... 131
Figure 7-3: Pneumatic Connections–MGFC7000E with Zero/Span/Shutoff Valves (OPT 50).... 134
Figure 7-4 Pneumatic Connections–MGFC7000E with Zero/Span/Shutoff Valves and External
Zero Air Scrubber (OPT 51)........................................................................ 134
Figure 7-5: Pneumatic Connections–MGFC7000E with Zero/Span Valves (OPT 52) ............... 135