Teledyne GFC-7000E - Trace CO2 Analyzer User Manual

Page 10

Model GFC7000E Instruction Manual GFC7000E

Documentation

04584 Rev A1

Table 6-2: Test Functions Defined................................................................................... 46

Table 6-3: List of Warning Messages ............................................................................... 49

Table 6-4: Primary Setup Mode Features and Functions ..................................................... 52

Table 6-5: Secondary Setup Mode Features and Functions ................................................. 52

Table 6-6: Variable Names (VARS) Revision B.3 ............................................................... 64

Table 6-7: GFC7000E Diagnostic (DIAG) Functions............................................................ 66

Table 6-8: DIAG - Analog I/O Functions........................................................................... 69

Table 6-9: Analog Output Voltage Ranges........................................................................ 69

Table 6-10: Analog Output Current Loop Range .................................................................. 70

Table 6-11: Analog Output Pin Assignments....................................................................... 70

Table 6-12: Voltage Tolerances for Analog Output Calibration ............................................... 73

Table 6-13: Current Loop Output Calibration with Resistor ................................................... 76

Table 6-14: Test Parameters Available for Analog Output A3 ................................................ 81

Table 6-15: COM1 and COM2 DB-9 Pin Assignments............................................................ 85

Table 6-16: COMM Port Communication modes................................................................... 86

Table 6-17: Ethernet Status Indicators .............................................................................. 89

Table 6-18: LAN/Internet Configuration Properties .............................................................. 90

Table 6-19: Internet Configuration Keypad Functions .......................................................... 94

Table 6-20: CO

Concentration Alarm Default Settings......................................................... 95

Table 6-21: Front Panel LED Status Indicators for iDAS ....................................................... 96

Table 6-22: iDAS Data Channel Properties ......................................................................... 97

Table 6-23: iDAS Data Parameter Functions....................................................................... 98

Table 6-24: Status Output Pin Assignments ..................................................................... 116

Table 6-25: Control Input Pin Assignments ...................................................................... 116

Table 6-26: Terminal Mode Software Commands .............................................................. 118

Table 6-27: Command Types ......................................................................................... 119

Table 6-28: Serial Interface Documents........................................................................... 123

Table 6-29: RS-232 Communication Parameters for Hessen Protocol ................................... 124

Table 6-30: Teledyne Instruments Hessen Protocol Response Modes ................................... 126

Table 6-31: Default Hessen Status Bit Assignments........................................................... 127

Table 7-1: AUTOCAL Modes ......................................................................................... 139

Table 7-2: AutoCal ATTRIBUTE Setup Parameters ........................................................... 139

Table 7-3: Calibration Data Quality Evaluation................................................................ 142

Table 9-1: GFC7000E Maintenance Schedule .................................................................. 146

Table 9-2: GFC7000E Test Function Record.................................................................... 147

Table 9-3: Predictive uses for Test Functions.................................................................. 148

Table 10-1: Sync/Demod Status LED Activity ................................................................... 168

Table 10-2: Relay Board Status LED’s ............................................................................. 169

Table 10-3: Front Panel Status LED’s .............................................................................. 176

Table 11-1: Warning Messages - Indicated Failures ........................................................... 185

Table 11-2: Test Functions - Indicated Failures................................................................. 187

Table 11-3: Sync/Demod Board Status Failure Indications ................................................. 190

Table 11-4:

Status LED Failure Indications ................................................................. 191

Table 11-5: Relay Board Status LED Failure Indications ..................................................... 192

Table 11-6: DC Power Test Point and Wiring Color Codes ................................................... 200

Table 11-7: DC Power Supply Acceptable Levels ............................................................... 200

Table 11-8: Relay Board Control Devices ......................................................................... 201

Table 11-9: Opto Pickup Board Nominal Output Frequencies............................................... 202

Table 11-10: Analog Output Test Function - Nominal Values Voltage Outputs.......................... 204

Table 11-11: Analog Output Test Function - Nominal Values Current Outputs ......................... 205

Table 11-12: Status Outputs Check .................................................................................. 205

Table 12-1: Static Generation Voltages for Typical Activities ............................................... 214

Table 12-2: Sensitivity of Electronic Devices to Damage by ESD ......................................... 214

Table A-1: GFC7000E Setup Variables, Revision E.0 ........................................................ 231