Yokogawa Removable Chassis DX1000N - Manual (Page 157)

3-40
IM 04L41B01-17E
Example Set the trend interval to the secondary trend
interval.
CV1
MS Writes a message (display and
write)
Syntax MS p1,p2,p3,p4
p1 Message number (1 to 100)
p2 Message write destination
GROUP A specified display group
ALL
All display groups
All display groups in the specified
batch group number (p4) when
multi batch /BT2 is in use
p3 Display group number
The display group number when p2 is set to
GROUP
Carries no meaning when p2 is set to ALL
p4 Message write destination batch group
number
Example Write the message in message number 8 to
display group 1.
MS8,GROUP,1
Description • If you omit p2, the message is written to all
display groups.
• Parameter p4 is only valid when multi batch
/BT2 is in use. When multi batch /BT2 is in
use, you cannot omit p4.
• Set parameters p3 and p4 by referring to the
table in section 3.3.
BJ Write a free message
Syntax BJ p1,p2,p3,p4,p5
p1 Message number (1 to 10)
p2 Message (up to 32 characters)
p3 Message write destination
GROUP A specified display group
ALL
All display groups
All display groups in the specified
batch group number (p5) when
multi batch /BT2 is in use
p4 Display group number
The display group number when p2 is set to
GROUP
Carries no meaning when p2 is set to ALL
p5 Message write destination batch group
number
Example Using message number 3, write the string
“ALARM” to all groups.
BJ3,ALARM,ALL
Description • If you omit p3, the message is written to all
display groups.
• Parameter p5 is only valid when multi batch
/BT2 is in use. When multi batch /BT2 is in
use, you cannot omit p5.
• Set parameters p3, p4, and p5 by referring to
the table in section 3.3.
EJ Changes the login password
Syntax EJ p1,p2,p3
p1 Old password (see the description)
p2 New password (see the description)
p3 New password (see the description)
Example Change the password from “PASS001” to
“WORD005.”
EJPASS001,WORD005,WORD005
Description • The password character lengths are indicated
below.
Release numbers 3 and earlier:
Up to 8 characters
Release numbers 4 and later:
Up to 20 characters
On models with the /AS1 advanced security
option: Between 6 and 20 characters
• When you use password management (the
WU command) on models with the /AS1
advanced security option, this command is
invalid.
TL Starts, stops, resets
computation (MATH) or clears
the computation dropout status
display
Syntax TL p1,p2
p1 Type of operation
0 Start computation
1 Stop computation
2 Reset computation
3 Clear the computation data
dropout display
p2 Batch group number
0 All computation channels
1, 2, ... Batch group number
Example Start computation.
TL0
Description • You cannot use this command while the DX is
saving or loading setup data.
• You can use this command on models with the
/M1 or /PM1 option.
• When multi batch /BT2 is in use, p2 is valid
when p1 is set to 2 (reset computation). If you
omit p2, it is the same as setting p2 to zero. If
p2 is set to zero, the DX resets the values of
all computation channels.
• Set parameter p2 by referring to the table in
section 3.3.
DS Switches the execution mode
between operation and setting
Syntax DS p1
3.5 Control Commands