Yamaha DME - Manual (Page 462)

Chapter 6 Component Guide
DME Designer Owner’s Manual 462
Delay->ER.
One input, two
output delay and
early reflections
effects in series. Delay L 0.0 to 1000.0 ms Left channel delay time
Delay R 0.0 to 1000.0 ms Right channel delay time
FB.Dly 0.0 to 1000.0 ms Feedback delay time
FB.Gain -99 to +99% Feedback gain (plus values for normal-phase
feedback, minus values for reverse-phase
feedback)
Hi.Ratio 0.1 to 1.0 High-frequency feedback ratio
HPF THRU, 21.2 Hz to 8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz to 16.0 kHz, THRU Low-pass filter cutoff frequency
DLY.BAL 0 to 100% Delay and early reflected delay balance (0% = all
early reflected delay, 100% = all delay)
Type S-Hall, L-Hall, Random, Revers,
Plate, Spring Type of early reflection simulation
RoomSize 0.1 to 20.0 Reflection spacing
Liveness 0 to 10 Early reflections decay characteristics (0 = dead,
10 = live)
Ini.Dly 0.0 to 500.0 ms Initial delay before reverb begins
Diff. 0 to 10 Spread
Density 0 to 100% Reverb density
ER Num. 1 to 19 Number of early reflections
Delay+Reverb
One input, two
output delay and
reverb effects in
parallel. Delay L 0.0 to 1000.0 ms Left channel delay time
Delay R 0.0 to 1000.0 ms Right channel delay time
FB.Dly 0.0 to 1000.0 ms Feedback delay time
FB.Gain -99 to +99% Feedback gain (plus values for normal-phase
feedback, minus values for reverse-phase
feedback)
Delay Hi 0.1 to 1.0 Delay high-frequency feedback ratio
HPF THRU, 21.2 Hz to 8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz to 16.0 kHz, THRU Low-pass filter cutoff frequency
Dly/Rev 0 to 100% Delay and reverb balance (0% = all delay, 100% =
all reverb)
Rev Time 0.3 to 99.0 s Reverb time
Ini.Dly 0.0 to 500.0 ms Initial delay before reverb begins
Rev Hi 0.1 to 1.0 High-frequency reverb time ratio
Diff. 0 to 10 Spread
Density 0 to 100% Reverb density
Delay->Reverb
One input, two
output delay and
reverb effects in
series. Delay L 0.0 to 1000.0 ms Left channel delay time
Delay R 0.0 to 1000.0 ms Right channel delay time
FB.Dly 0.0 to 1000.0 ms Feedback delay time
FB.Gain -99 to +99% Feedback gain (plus values for normal-phase
feedback, minus values for reverse-phase
feedback)
Delay Hi 0.1 to 1.0 Delay high-frequency feedback ratio
HPF THRU, 21.2 Hz to 8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz to 16.0 kHz, THRU Low-pass filter cutoff frequency
Dly.Bal 0 to 100% Delay and delayed reverb balance (0% = all
delayed reverb, 100% = all delay)
Rev Time 0.3 to 99.0 s Reverb time
Ini.Dly 0.0 to 500.0 ms Initial delay before reverb begins
Rev Hi 0.1 to 1.0 High-frequency reverb time ratio
Diff. 0 to 10 Spread
Density 0 to 100% Reverb density
Effect Type Parameter Setting Range Function