Yamaha DME - Manual (Page 455)

Chapter 6 Component Guide
DME Designer Owner’s Manual 455
Other effect parameters vary according to the selected effect type, as shown below.
Effect Type Parameter Setting Range Function
Reverb Hall
Reverb Room
Reverb Stage
Reverb Plate
One input, two
output hall, room,
stage, and plate
reverb simulations,
all with gates. Rev Time 0.3 to 99.0 s Reverb time
Ini.Dly 0.0 to 500.0 ms Initial delay before reverb begins
Hi.Ratio 0.1 to 1.0 High-frequency reverb time ratio
Lo.Ratio 0.1 to 2.4 Low-frequency reverb time ratio
Diff. 0 to 10 Reverb diffusion (left-right reverb spread)
Density 0 to 100% Reverb density
E/R Dly 0.0 to 100.0 ms Delay between early reflections and reverb
E/R Bal. 0 to 100% Balance of early reflections and reverb (0% = all
reverb, 100% = all early reflections)
HPF THRU, 21.2 Hz to 8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz to 16.0 kHz, THRU Low-pass filter cutoff frequency
Gate Lvl OFF, -60 to 0 dB Level at which gate kicks in
Attack 0 to 120 ms Gate opening speed
Hold 44.1kHz: 0.02ms to 2.13s
48kHz: 0.02 ms to 1.96s
88.2kHz: 0.01ms to 1.06s
96kHz: 0.01ms to 981ms Gate open time
Decay 44.1kHz: 6.0ms to 46.0s
48kHz: 5.0ms to 42.3s
88.2kHz: 3ms to 23.0s
96kHz: 3ms to 21.1s Gate closing speed
Early Ref.
One input, two
output early
reflections. Type S-Hall, L-Hall, Random, Revers,
Plate, Spring Type of early reflection simulation
RoomSize 0.1 to 20.0 Reflection spacing
Liveness 0 to 10 Early reflections decay characteristics (0 = dead,
10 = live)
Ini.Dly 0.0 to 500.0 ms Initial delay before reverb begins
Diff. 0 to 10 Reflection diffusion (left-right reflection spread)
Density 0 to 100% Reflection density
ER Num. 1 to 19 Number of early reflections
FB.Gain -99 to +99% Feedback gain
Hi.Ratio 0.1 to 1.0 High-frequency feedback ratio
HPF THRU, 21.2 Hz to 8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz to 16.0 kHz, THRU Low-pass filter cutoff frequency
Gate Reverb
Reverse Gate
One input, two
output early
reflections with
gate, and early
reflections with
reverse gate. Type Type-A, Type-B Type of early reflection simulation
RoomSize 0.1 to 20.0 Reflection spacing
Liveness 0 to 10 Early reflections decay characteristics (0 = dead,
10 = live)
Ini.Dly 0.0 to 500.0 ms Initial delay before reverb begins
Diff. 0 to 10 Reflection diffusion (left-right reflection spread)
Density 0 to 100% Reflection density
ER Num. 1 to 19 Number of early reflections
FB.Gain -99 to +99% Feedback gain
Hi.Ratio 0.1 to 1.0 High-frequency feedback ratio
HPF THRU, 21.2 Hz to 8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz to 16.0 kHz, THRU Low-pass filter cutoff frequency
Mono Delay
One input, one
output basic repeat
delay. Delay 0.0 to 2730.0 ms Delay time
FB.Gain -99 to +99% Feedback gain (plus values for normal-phase
feedback, minus values for reverse-phase
feedback)
Hi.Ratio 0.1 to 1.0 High-frequency feedback ratio
HPF THRU, 21.2 Hz to 8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz to 16.0 kHz, THRU Low-pass filter cutoff frequency