Rockwell Automation 20D PowerFlex 700S Drive Ph I Control, Frames 1...11 - Manual (Page 70)

3-16 Programming and Parameters
Parameter Data in Linear
List Format
No.
Name
Description
Values Li
nka
b
le
Rea
d
-W
ri
te
Da
ta
T
yp
e
1 Motor NP Volts
Set to the motor nameplate rated volts.
Units:
Default:
Min/Max: Volt
Calculated
75/705 ✓ 16-bit
Integer
2 Motor NP FLA
Set to the motor nameplate rated full load amps. Range limited by three-second inverter
rating.
Units:
Default:
Min/Max: Amps
Calculated
Calculated/Calculated ✓ Real
3 Motor NP Hertz
Set to the motor nameplate rated frequency.
Units:
Default:
Min/Max: Hz
Calculated
2.0000/500.0000 ✓ Real
4 Motor NP RPM
Set to the motor nameplate rated RPM.
Units:
Default:
Min/Max: RPM
Calculated
1/30000 ✓ 16-bit
Integer
5 Motor NP Power
Set to the motor nameplate rated power.
Units:
Default:
Min/Max: Hp
Calculated
0.2500/3500.0000 ✓ Real
6 Mtr NP Pwr Units
The power units shown on the motor nameplate.
Default:
Options: 0
0
1 Hp
Hp
W
7 Motor Poles
Set to the number of motor poles indicated on the motor nameplate. Only even numbers are
allowed.
Units:
Default:
Min/Max: Pole
4
2/40 ✓ 16-bit
Integer
8 Motor Inertia
Time, in seconds, for an uncoupled motor to accelerate from zero to base speed, at rated
motor torque. Calculated during autotune.
Units:
Default:
Min/Max: Sec
0.400
0.0100/655.0000 ✓ ✓ Real
9 Total Inertia
Time, in seconds, for a motor coupled to a load to accelerate from zero to base speed, at
rated motor torque. Calculated during autotune.
Units:
Default:
Min/Max: Sec
2.0000
0.0100/655.0000 ✓ ✓ Real
10 Speed Ref 1
Sets the speed reference that the drive should use when selected by Par 16 [Speed Ref Sel].
A value of 1.0 represents base speed of the motor.
Default:
Min/Max: 0.0000
-/+2200000000.0000 ✓ ✓ Real
11 Spd Ref1 Divide
Par 10 [Speed Ref 1] is divided by this number. This number can be used to scale the value
of Par 10 [Speed Ref 1].
Default:
Min/Max: 1.0000
-/+2200000000.0000 ✓ ✓ Real
12 Speed Ref 2
Sets the speed reference that the drive should use when selected by Par 16 [Speed Ref Sel].
A value of 1.0 represents base speed of the motor.
Default:
Min/Max: 0.0000
-/+2200000000.0000 ✓ ✓ Real
13 Spd Ref2 Multi
Par 12 [Speed Ref 2] is multiplied by this number. This number can be used to scale the
value of Par 12 [Speed Ref 2].
Default:
Min/Max: 1.0000
-/+2200000000.0000 ✓ ✓ Real
14 Speed Ref 4
Sets the speed reference that the drive should use when selected by Par 16 [Speed Ref Sel].
Units:
Default:
Min/Max:
Comm Scale: RPM
0.0000
-/+14112.0000
Par 4 [Motor NP RPM] = 1.0 ✓ ✓ Real
15 Speed Ref 5
Sets the speed reference that the drive should use when selected by Par 16 [Speed Ref Sel].
Units:
Default:
Min/Max:
Comm Scale: RPM
0.0000
-/+14112.0000
Par 4[Motor NP RPM] = 1.0 ✓ ✓ Real
16 Speed Ref Sel
Selects the source of the speed reference to the drive.
Default:
Options: 1
0
1
2
3 “Spd Ref DPI”
“Zero Speed”
4 “Spd Ref 4”
“Spd Ref 1 5 “Spd Ref 5”
“Spd Ref 2” 6 “Spd Ref DPI”
“Spd Ref 3
17 Jog Speed 1
Sets the speed reference that the drive should use when responding to bit 18 [Jog 1] of Par
152 [Applied LogicCmd].
Units:
Default:
Min/Max:
Comm Scale: RPM
0.0000
-/+14112.0000
Par 4 [Motor NP RPM] = 1.0 ✓ ✓ Real
18 Jog Speed 2
Sets the speed reference that the drive should use when responding to bit 23 [Jog 2] of Par
152 [Applied LogicCmd].
Units:
Default:
Min/Max:
Comm Scale: RPM
0.0000
-/+14112.0000
Par 4 [Motor NP RPM] = 1.0 ✓ ✓ Real
19 Atune Spd Ref
Sets the maximum speed of the motor during the Flux current and inertia tests.
Units:
Default:
Min/Max:
Comm Scale: RPM
1499.4000
176.4000/1764.0000
Par 4 [Motor NP RPM] = 1.0 ✓ Real