Rockwell Automation 20D PowerFlex 700S Drive Ph I Control, Frames 1...11 - Manual (Page 106)

3-52 Programming and Parameters
390 SL MultErr Cnfg
Enter a value to configure the Drive Module's response to SynchLink Multiplier error.
Refer to Par 1034 [SL Mult State] for possible causes for multiplier errors.
• 0 “Ignore” - Configures the drive to continue running, as normal, when this event
occurs
• 1 “Alarm” - Configures the drive to continue running and set the appropriate alarm bit
when this event occurs
• 2 “FltCoastStop” - Configures the drive to perform a coast stop and set the appropriate
fault bit, in response this event
• 3 “Flt RampStop” - Configures the drive to perform a ramp stop and set the
appropriate fault bit, in response this event
• 4 “FltCurLimStp” - Configures the drive to perform a current-limit stop and set the
appropriate fault bit, in response this event
Default:
Options: 2
0
1
2
3
4 “FltCoastStop”
“Ignore”
“Alarm”
“FltCoastStop”
“Flt RampStop”
“FltCurLimStp”
391 DPI CommLoss Cfg
Enter a value to configure the drive's response to the failure of a DPI port.
• 0 “Ignore” - Configures the drive to continue running, as normal, when this event
occurs
• 1 “Alarm” - Configures the drive to continue running and set the appropriate alarm bit
when this event occurs
• 2 “FltCoastStop” - Configures the drive to perform a coast stop and set the appropriate
fault bit, in response this event
• 3 “Flt RampStop” - Configures the drive to perform a ramp stop and set the
appropriate fault bit, in response this event
• 4 “FltCurLimStp” - Configures the drive to perform a current-limit stop and set the
appropriate fault bit, in response this event
Default:
Options: 2
0
1
2
3
4 “FltCoastStop”
“Ignore”
“Alarm”
“FltCoastStop”
“Flt RampStop”
“FltCurLimStp”
392 NetLoss DPI Cnfg
Enter a value to configure the drive's response to communication fault from a network
card at a DPI port.
• 0 “Ignore” - Configures the drive to continue running, as normal, when this event
occurs
• 1 “Alarm” - Configures the drive to continue running and set the appropriate alarm bit
when this event occurs
• 2 “FltCoastStop” - Configures the drive to perform a coast stop and set the appropriate
fault bit, in response this event
• 3 “Flt RampStop” - Configures the drive to perform a ramp stop and set the
appropriate fault bit, in response this event
• 4 “FltCurLimStp” - Configures the drive to perform a current-limit stop and set the
appropriate fault bit, in response this event
Default:
Options: 2
0
1
2
3
4 “FltCoastStop”
“Ignore”
“Alarm”
“FltCoastStop”
“Flt RampStop”
“FltCurLimStp”
393 BusUndervoltCnfg
Enter a value to configure the drive's response to DC Bus voltage falling below the
minimum value.
• 0 “Ignore” - Configures the drive to continue running, as normal, when this event
occurs
• 1 “Alarm” - Configures the drive to continue running and set the appropriate alarm bit
when this event occurs
• 2 “FltCoastStop” - Configures the drive to perform a coast stop and set the appropriate
fault bit, in response this event
Default:
Options: 1
0
1
2 “Alarm”
“Ignore”
“Alarm”
“FltCoastStop”
No.
Name
Description
Values Li
nkab
le
Read
-Wr
it
e
Da
ta
T
ype
!
ATTENTION: Risk of injury or equipment damage exists. Parameter 390 [SL MultErr Cnfg] lets you determine the action
of the drive if communications are disrupted. By default this parameter causes the drive to fault and coast to a stop. You can
set this parameter so that the drive continues to run. Precautions should be taken to ensure that the setting of this parameter
does not create hazards of injury or equipment damage.
!
ATTENTION: Risk of injury or equipment damage exists. Parameter 391 [DPI CommLoss Cfg] lets you determine the
action of the drive if communications are disrupted. By default this parameter causes the drive to fault and coast to a stop.
You can set this parameter so that the drive continues to run. Precautions should be taken to ensure that the setting of this
parameter does not create hazards of injury or equipment damage.
!
ATTENTION: Risk of injury or equipment damage exists. Parameter 392 [NetLoss DPI Cnfg] lets you determine the
action of the drive if communications are disrupted. By default this parameter causes the drive to fault and coast to a stop.
You can set this parameter so that the drive continues to run. Precautions should be taken to ensure that the setting of this
parameter does not create hazards of injury or equipment damage.