Rockwell Automation 20D PowerFlex 700S Drive Ph I Control, Frames 1...11 - Manual (Page 136)

3-82 Programming and Parameters
1013 SL Rx DirectSel2
Determines the destination for the data received at word 2 of direct received data.
Configure the selection by using the Peer Communication window in the DriveExecutive
programming software.
Default:
Options: 0
0
1
2
3
4
5 “No Data”
“No Data”
6 “Reserved”
“SL Multiply” 7 “Reserved”
“Event P0” 8 “Event Opt0”
“Reserved” 9 “Reserved”
“Reserved” 10 “Event Status”
“Reserved”
1014 SL Rx DirectSel3
Determines the destination for the data received at word 3 of direct received data.
Configure the selection by using the Peer Communication window in the DriveExecutive
programming software.
Default:
Options: 0
0
1
2
3
4
5 “No Data”
“No Data”
6 “Reserved”
“SL Multiply” 7 “Reserved”
“Event P0” 8 “Event Opt0”
“Reserved” 9 “Reserved”
“Reserved” 10 “Event Status”
“Reserved”
1020 SL Tx Comm Frmt
Defines the node's communication format for transmitting SynchLink data. This
determines the number of axis data words, direct data words and buffered data words
transmitted. Configure the format by using the Peer Communication window in the
DriveExecutive programming software.
1021 SL Tx DirectSel0
Determines the source type for the data transmitted by direct transmit word 0. The source
type selections are: no data, event, feedback and drive parameter. If drive parameter is
selected, a parameter of the appropriate data format (integer or real) must be linked to
Parameter 1141 [SL Dir Int Tx0] or Parameter 1142 [SL Dir Real Tx0]. Configure the
selection by using the Peer Communication window in the DriveExecutive programming
software.
Default:
Options: 0
0
1
2
3
4
5
6
7
8
9
10
11
12
13 “No Data”
“No Data”
14 “Reserved”
“SL Multiply” 15 “Reserved”
“Event P0” 16 “Reserved”
“Event P1” 17 “Reserved”
“Reserved” 18 “Reserved”
“Reserved” 19 “Reserved”
“Reserved” 20 “Reserved”
“Reserved” 21 “Dir Tx Data”
“Event Opt0” 22 “Dir Rx Data”
“Reserved” 23 “E0 Accum”
“Event Status” 24 “E1 Accum”
“Reserved” 25 “Opt0 Accum”
“Reserved” 26 “Opt1 Accum”
“Reserved”
1022 SL Tx DirectSel1
Determines the source type for the data transmitted by direct transmit word 1. The source
type selections are: no data, event, feedback and drive parameter. If drive parameter is
selected, a parameter of the appropriate data format (integer or real) must be linked to
Par 1143 [SL Dir Int Tx1] or Par 1144 [SL Dir Real Tx1]. Configure the selection by using
the Peer Communication window in the DriveExecutive programming software.
Default:
Options: 0
0
1
2
3
4
5
6
7
8
9
10
11
12
13 “No Data”
“No Data”
14 “Reserved”
“SL Multiply” 15 “Reserved”
“Event P0” 16 “Reserved”
“Event P1” 17 “Reserved”
“Reserved” 18 “Reserved”
“Reserved” 19 “Reserved”
“Reserved” 20 “Reserved”
“Reserved” 21 “Dir Tx Data”
“Event Opt0” 22 “Dir Rx Data”
“Reserved” 23 “E0 Accum”
“Event Status” 24 “E1 Accum”
“Reserved” 25 “Opt0 Accum”
“Reserved” 26 “Opt1 Accum”
“Reserved”
1023 SL Tx DirectSel2
Determines the source type for the data transmitted by direct transmit word 2. The source
type selections are: no data, event, feedback and drive parameter. If drive parameter is
selected, a parameter of the appropriate data format (integer or real) must be linked to
Parameter 1145 [SL Dir Int Tx2] or Parameter 1146 [SL Dir Real Tx2]. Configure the
selection by using the Peer Communication window in the DriveExecutive programming
software.
Default:
Options: 0
0
1
2
3
4
5
6
7
8
9
10
11
12
13 “No Data”
“No Data”
14 “Reserved”
“SL Multiply” 15 “Reserved”
“Event P0” 16 “Reserved”
“Event P1” 17 “Reserved”
“Reserved” 18 “Reserved”
“Reserved” 19 “Reserved”
“Reserved” 20 “Reserved”
“Reserved” 21 “Dir Tx Data”
“Event Opt0” 22 “Dir Rx Data”
“Reserved” 23 “E0 Accum”
“Event Status” 24 “E1 Accum”
“Reserved” 25 “Opt0 Accum”
“Reserved” 26 “Opt1 Accum”
“Reserved”
No.
Name
Description
Values Li
nkab
le
Read
-Wr
it
e
Da
ta
T
ype
Value Axis Direct Buffered
Options 0 0 0 0
7 0 2 18
9 0 4 8
17 0 4 18