ZyXEL Communications IES-612-51A User Manual
User’s guide
Table of contents
Document Outline
- User’s Guide
- Introduction
- Basic Settings
- Introducing the Web Configurator
- Initial Configuration
- Home and Port Statistics Screens
- System Information
- General Setup
- User Account
- Switch Setup
- IP Setup
- ENET Port Setup
- xDSL Port Setup
- xDSL Profiles Setup
- xDSL Line Data
- Advanced Application
- Routing Protocol, Alarm and Management
- CLI Commands
- Commands Summary
- Command Examples
- Alarm Commands
- 43.1 Alarm Commands
- 43.2 General Alarm Command Parameters
- 43.3 Alarm Show Command
- 43.4 Alarm Port Show Command
- 43.5 Alarm Port Set Command
- 43.6 Alarm Tablelist Command
- 43.7 Log Format
- 43.8 Alarm History Show Command
- 43.9 Alarm History Clear Command
- 43.10 Alarm XEdit Command
- 43.11 Alarm Cutoff Command
- 43.12 Alarm Clear Command
- DHCP Commands
- IEEE 802.1Q Tagged VLAN Commands
- MAC Commands
- IGMP Commands
- Packet Filter Commands
- IP Commands
- Firmware and Configuration File Maintenance Commands
- SNMP Commands
- ADSL Commands
- 52.1 DSL Port Commands
- 52.1.1 DSL Port Show Command
- 52.1.2 DSL Port Enable Command
- 52.1.3 DSL Port Disable Command
- 52.1.4 DSL Port Profile Show Command
- 52.1.5 DSL Port Profile Set Command
- 52.1.6 DSL Port Profile Delete Command
- 52.1.7 DSL Port Profile Map Command
- 52.1.8 DSL Port Name Command
- 52.1.9 DSL Port Tel Command
- 52.1.10 DSL Port Loopback Command
- 52.1.11 DSL Port Upstream PSD Command
- 52.1.12 DSL Port Downstream PSD Command
- 52.1.13 DSL Port Upstream Carrier Command
- 52.1.14 DSL Port Downstream Carrier0 Command
- 52.1.15 DSL Port Downstream Carrier1 Command
- 52.1.16 PMM Parameters Command
- 52.1.17 Impulse Noise Protection Command
- 52.1.18 Annex L Enable Command
- 52.1.19 Annex L Disable Command
- 52.1.20 Annex M Enable Command
- 52.1.21 Annex M Disable Command
- 52.1.22 Annex I Enable Command
- 52.1.23 Annex I Disable Command
- 52.2 DSL Port Statistics Commands
- 52.2.1 DSL Port Show Command
- 52.2.2 Linedata Command
- 52.2.3 Lineinfo Command
- 52.2.4 Lineperf Command
- 52.2.5 15 Minute Performance Command
- 52.2.6 1 Day Performance Command
- 52.2.7 Line Diagnostics Set Command
- 52.2.8 Line Diagnostics Get Command
- 52.2.9 Line Diagnostics Get 992.3 Command
- 52.2.10 SELT Diagnostic Set Command
- 52.2.11 SELT Diagnostic Get Command
- 52.2.12 Tone Diagnostics 992.3 Command
- 52.3 Alarm Profile Commands
- 52.1 DSL Port Commands
- Virtual Channel Management Commands
- 53.1 Virtual Channel Management Overview
- 53.2 Virtual Channel Profile Commands
- 53.3 PVC Channels
- 53.4 Priority-based PVCs
- 53.5 PPVC Member Delete Command
- 53.6 PPVC Member Show Command
- 53.7 2684 Routed Mode Commands
- 53.7.1 2684 Routed Mode Example
- 53.7.2 RPVC Gateway Set Command
- 53.7.3 RPVC Gateway Show Command
- 53.7.4 RPVC Gateway Delete Command
- 53.7.5 RPVC Set Command
- 53.7.6 RPVC Show Command
- 53.7.7 RPVC Delete Command
- 53.7.8 RPVC Route Set Command
- 53.7.9 RPVC Route Show Command
- 53.7.10 RPVC Route Delete Command
- 53.7.11 RPVC ARP Agingtime Set Command
- 53.7.12 RPVC ARP Agingtime Show Command
- 53.7.13 RPVC ARP Show Command
- 53.7.14 RPVC ARP Flush Command
- 53.8 PPPoA to PPPoE (PAE) Commands
- 53.9 Transparent LAN Service (TLS) Commands
- ACL Commands
- Troubleshooting and Specifications
- Troubleshooting
- 55.1 The SYS LED Does Not Turn On
- 55.2 The ALM LED Is On
- 55.3 LAN Port LEDs Do Not Turn On
- 55.4 LAN Port Data Transmission
- 55.5 DSL Data Transmission
- 55.6 There Is No Voice on a DSL Connection
- 55.7 Testing Wiring
- 55.8 Local Server
- 55.9 Data Rate
- 55.10 Configured Settings
- 55.11 Password
- 55.12 System Lockout
- 55.13 SNMP
- 55.14 Telnet
- 55.15 Resetting the Defaults
- 55.16 Recovering the Firmware
- Product Specifications
- Troubleshooting
- Appendices and Index