Yaskawa J50M Instructions User Manual
Page 95
(3)
Setting and displaying tool life control data:
The tool numbers used in each tool group and the tool
compensation number, life, total usages, etc. of each tool
can be entered
from the
or can
be input from the part-program.
tool life
-
control data
can also be displayed with the
function.
T O O L L I F E C O N T R O L 0 1 2 3 4
001 002 003 004 005 007 009 010
012 014 015 017 018 022 025 030
031 032 033 034 035
043 048
051 066 067 068 069 070 072 073
074 075 077 078 079 080 081 082
084 084 085 086 087 088 089 090
091 092 093 085 099 100 101 102
103 104 105 111 122 128 * *
REGISTERED GROUP NO.
R D Y
2.9.32.2
DISPLAY
With the function set to
, tool life control data are
displayed bydepressing
The
key
is a two stage switch for offset display and tool life con-
trol display.
(1) List oftoollife control group registrations
Pages 1 and 2 of the tool life control display shows a
list of registered tool groups. Check the information
on these pages for any groupto be indexed.
(2) Tool life control data display
Page 3 and subsequent pages of the tool life control
display are the tool life control data display. Each
tool group composes a 2-page data display screen.
Using “group search’’
convenient to display the
desired page.
(a) Press the key to display the tool life control screen. (b) Press the key to display the tool life control data screen. (c) Key-in value of the object group. (d) Press the group will then appear. key. Data display of the object GROUP NO. LIFE CLASSIFICATION TOOL LIFE CONTROL 01234 GROUP 123-1 MINUTES T - N O H - N O D - N O L I F E U S E D S T S 001 002 300 302 OVR 011 012 400 400 OVR TO024 100 101 500 153 SKP 212 214 1000 25 TOO05 023 022 9000 00 * * 500 0 TO054 099 00 200 0 * * * TOOL NO. TOOL RADIUS U N R E G I S T E R E D C O M P E N S A T I O N U S A G E S M A R K TOOL LIFE I TOOL LENGTH TOOL LIFE C O M P E N S A T I O N EXPIRED NO. SKP-SKIPPED TOOL 2.9.32.3 TOOL LIFE CONTROL DATA (1) Setting by key input Writing and correcting of tool life control data can be performed from the operator’s panel. (a) Sequence of operation (i) Press the key to display the tool life control screen. (ii ) Use the key or group search and search the group to be rewritten. (iii) Since the cursor will be at the first T-NO, move key. (The cursor moves horizontally.) (iv) Key-in the numerical value. ( v ) Press the key. The data at the cursor posi- tion will then be rewritten. (b) Writing T-NO If the cursor is placed under a registered T-NO and a (c) Writing H-NO and D-NO (i) When a command such as H999 or D999 is given from the part program, the corrected numbers (ii) As long as nothing in particular is written i n H - N O a n d D - N O , t h e y w i l l b e c o n s i d e r e d (iii) Unregistered and H-NO = O are different. H-NO = O and D-NO = O are corrections cancelled, if H (D) 999 is executed in unregistered (iv) Key-in numerical values from O to 299 for H-NO and D-NO. (d) Writing LIFE (i) The numerical value 9999 will be automatically written when T-NO is written. 87
the cursor to the T-NO by pressing the
new T-NO is entered, the other data will be initialized
and LIFE = 9999, H-NO and D-NO will be unregis-
tered (* mark), and USED = O STS will be blank.
in a numerical value between O - 9998 for the T–NO.
stored here will be searched.
unregistered (* mark) .
state, an error will occur.