Brocade Communications Systems RFS6000 - Manual (Page 671)

Brocade Mobility RFS4000, RFS6000 and RFS7000 CLI Reference Guide 669
53-1001931-01
Wireless configuration commands
20
See also, “service” on page 37.
Usage Guidelines
To stop a service, use the
no
command. For instance, use
no service wireless idle-radio-send-multicast enable
to stop sending
broadcast/multicast frames to idle radios
Example
RFController(config-wireless)#service show wireless ap-history
AP MAC Radio Timestamp Event Reason
===================================================================
00-A0-F8-BF-8A-4B N/A 20100926-20:23:10 Adoption N/A
RFController(config-wireless)#
RFController(config-wireless)#service show wireless mvlan 20
Wlan 20: pool_size =1
-----------------------------------------------------
[ 0]: wlan=20, vlan_id=1, limit=0, users=0, log_sent=0
[ 1]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[ 2]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[ 3]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[ 4]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[ 5]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[ 6]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[ 7]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[ 8]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[ 9]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[10]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[11]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[12]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[13]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[14]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[15]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
•
free-packet-watermark <0-100>– The free packets
threshold in percent. If the percentage of free packets is
lower than this number, then additional packets will not be
queued in the datapath.
•
idle-radio-send-multicast enable – Enables forwarding
multicast packets to radios without associated wireless
clients.
•
legacy-load-balance – Invoke legacy load balance algorithm.
•
map-radios <1-127> – Sets radio-to-cpu mapping constant
to a value in the range of 1 and 127.
•
radio-misc-cfg – Radio specific
miscellaneous U16 configuration for all radios.
•
rate-scale – Enable wireless rate scaling (default).
•
request-ap-log <1-1024> – Request AP Log for the selected
AP.
•
save-ap-log – Saves debug/error logs sent by the
access-point
•
snmp-trap-throttle <1-20> – Limits the number of SNMP
traps generated per second from the wireless module to a
number in the range 1 and 20.
•
sync-radio-entries – sync radio configuration at cluster levels.
•
vlan-cache enable – Enables VLAN-cache mode.