Rockwell Automation 1771-QI,D17716.5.126 PLASTIC MOLD.MODULE - Manual (Page 9)

Table of Contents toc–v
Publication 1771-6.5.126– March 1998
PPS – Plastication Profile Status Block 3–8 . . . . . . . . . . . . . . . . . . . . .
Bit-mapped Status Words 3–8 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Plastication Profile Actuals 3–9 . . . . . . . . . . . . . . . . . . . . . . . . . .
Plastication Maximum Pressure 3–10 . . . . . . . . . . . . . . . . . . . . . .
Post-decompression Maximum Pressure 3–10 . . . . . . . . . . . . . . . .
Execution Times 3–11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Post-decompression Movement Actuals 3–11 . . . . . . . . . . . . . . . .
Shot Size Actual 3–11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PTS – Process Trace Status Block 3–11 . . . . . . . . . . . . . . . . . . . . . . . .
Bit-mapped Status Words 3–11 . . . . . . . . . . . . . . . . . . . . . . . . . . .
RLS – Inject ERC Values Status Block 3–13 . . . . . . . . . . . . . . . . . . . . .
Bit-mapped Status Words 3–13 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Injection Profile ERC Actuals 3–13 . . . . . . . . . . . . . . . . . . . . . . . .
Pack Profile ERC Actuals 3–13 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hold Profile ERC Actuals 3–13 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Plastication Profile ERC Actuals 3–13 . . . . . . . . . . . . . . . . . . . . . .
SYS – System Status Block 3–14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bit-mapped Status Words 3–14 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Level In Engineering Units 3–24 . . . . . . . . . . . . . . . . . . . . . .
Input Level, Raw Signal 3–24 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Level in Percentage 3–24 . . . . . . . . . . . . . . . . . . . . . . . . . .
Cycle Maximum Pressures 3–25 . . . . . . . . . . . . . . . . . . . . . . . . . .
Process Trace Data Collection Status 3–25 . . . . . . . . . . . . . . . . . .
Process Times 3–26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostics 3–26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
New Status Confirmation 3–26 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 4
How to Read Error Codes 4–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ID = 1 MCC – Module Configuration Command Block 4–3 . . . . . .
ID = 2 JGC – Jog Configuration Block 4–6 . . . . . . . . . . . . . . . . . .
ID = 8 INC – Injection Configuration Block 4–7 . . . . . . . . . . . . . . .
ID = 9 IPC – Injection Profile Block 4–9 . . . . . . . . . . . . . . . . . . . .
ID = 10 PKC – Pack Configuration Block 4–15 . . . . . . . . . . . . . . . .
ID = 11 HDC – Hold Configuration Block 4–16 . . . . . . . . . . . . . . . .
ID = 12 HPC – Pack/Hold Profile Block 4–17 . . . . . . . . . . . . . . . . .
ID = 13 PRC – Pre-Decompression Configuration Block . 4–20 . . . .
ID = 14 PLC – Plastication Configuration Block 4–21 . . . . . . . . . . . .
ID = 15 PPC – Plastication Profile Block 4–22 . . . . . . . . . . . . . . . .
ID = 16 PSC – Post-Decompression Configuration Block . 4–28 . . . .
ID = 25 DYC – Dynamic Command Block 4–29 . . . . . . . . . . . . . . .
ID = 26 RLC – Inject ERC Values Block 4–29 . . . . . . . . . . . . . . . . .
ID = 28 PTC – Process Trace Configuration Block 4–30 . . . . . . . . .
Programming
Error Codes