Rockwell Automation 1771-QI,D17716.5.126 PLASTIC MOLD.MODULE - Manual (Page 10)

Table of Contents toc–vi
Publication 1771-6.5.126– March 1998
Chapter 5
Chapter Objectives 5–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A, Only or B, Only 5–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A and B 5–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A then B 5–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard Programming 5–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Co-injection Programming 5–2 . . . . . . . . . . . . . . . . . . . . . . . . . .
Suspended Outputs Are Turned Off 5–3 . . . . . . . . . . . . . . . . . . . .
Suspended Outputs Are Programmed 5–4 . . . . . . . . . . . . . . . . . .
During B, A Maintains Low Pressure or Flow (plateau) 5–5 . . . . . .
Flow Chart for Co-injection Programming 5–6 . . . . . . . . . . . . . . . . . . . .
Co-injection Diagram for ABA 5–6 . . . . . . . . . . . . . . . . . . . . . . . .
List of Co-injection Parameters for ABA 5–6 . . . . . . . . . . . . . . . . .
Flow Chart for A in Sequence ABA 5–7 . . . . . . . . . . . . . . . . . . . .
Flow Chart for Sequence ABA 5–8 . . . . . . . . . . . . . . . . . . . . . . .
Chapter 6
I/O Specifications 6–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environmental Conditions 6–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware Requirements 6–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Process Control Options 6–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 7
Calibration Equipment Required 7–1 . . . . . . . . . . . . . . . . . . . . . . . . . .
Map Your BTW and BTR Data Blocks 7–2 . . . . . . . . . . . . . . . . . . . . . .
Write Your Calibration Logic 7–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Internal Jumpers 7–3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wire the Wiring Arms 7–5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calibration Setup Using Optional Equipment 7–6 . . . . . . . . . . . . . . . . .
Calibration Setup at the Machine Location 7–6 . . . . . . . . . . . . . . . . . . .
Calibration Procedure for Inputs 7–7 . . . . . . . . . . . . . . . . . . . . . . . . . .
Calibration Procedure for Outputs 7–8 . . . . . . . . . . . . . . . . . . . . . . . . .
Sequencing Co-injection
Module Specifications
Calibration Instructions