Rockwell Automation 1771-QI,D17716.5.126 PLASTIC MOLD.MODULE - Manual (Page 129)

4–27 Programming Error Codes
Publication 1771-6.5.126 – March 1998
Error Code Description PPC ID = 15
0820 PPC20 must be 00000 when PPC16 = 00000.
0823 PPC23 must be 00000 when PPC19 = 00000.
0824 PPC24 must be 00000 when PPC20 = 00000.
0827 PPC27 must be 00000 when PPC23 = 00000.
0828 PPC28 must be 00000 when PPC24 = 00000.
0831 PPC31 must be 00000 when PPC27 = 00000.
0832 PPC32 must be 00000 when PPC28 = 00000.
0835 PPC35 must be 00000 when PPC31 = 00000.
0836 PPC36 must be 00000 when PPC32 = 00000.
0839 PPC39 must be 00000 when PPC35 = 00000.
0840 PPC40 must be 00000 when PPC36 = 00000.
0843 PPC43 must be 00000 when PPC39 = 00000.
0844 PPC44 must be 00000 when PPC40 = 00000.
0847 PPC47 must be 00000 when PPC43 = 00000.
0848 PPC48 must be 00000 when PPC44 = 00000.
0961 PPC61 is too large.
if:
then:
MCC13 and MCC14 PPC61 must be within MCC13 + PPC61 + PRC05
≤
MCC14
are both non-zero
MCC13 is zero and PPC61 must be within MCC09 + PPC61 + PRC05
≤
MCC14
is non-zero
MCC13 is non-zero and PPC61 must be within MCC13 + PPC61 + PRC05
≤
MCC10
MCC14 is zero
MCC13 and MCC14 PPC61 must be within MCC09 + PPC61 + PRC05
≤
MCC10
are both zero
0962 PPC62 is too large.
if:
then:
MCC13 and MCC14 PPC62 must be within MCC13 + PPC61 + PPC62 + PSC05
are both non-zero
≤
MCC14
MCC13 is zero and PPC62 must be within MCC09 + PPC61 + PPC62 + PSC05
MCC14 is non-zero
≤
MCC14
MCC13 is non-zero and PPC62 must be within MCC13 + PPC61 + PPC62 + PSC05
MCC14 is zero
≤
MCC10
MCC13 and MCC14 PPC62 must be within MCC09 + PPC61 + PPC62 + PSC05
are both zero
≤
MCC10
1015 PPC15 is not in increasing positional order.
If non-zero, PPC15 must be greater than PPC11.
1019 PPC19 is not in increasing positional order.
If non-zero, PPC19 must be greater than PPC15.
1023 PPC23 is not in increasing positional order.
If non-zero, PPC23 must be greater than PPC19.
1027 PPC27 is not in increasing positional order.
If non-zero, PPC27 must be greater than PPC23.
1031 PPC31 is not in increasing positional order.
If non-zero, PPC31 must be greater than PPC27.
1035 PPC35 is not in increasing positional order.
If non-zero, PPC35 must be greater than PPC31.
1039 PPC39 is not in increasing positional order.
If non-zero, PPC39 must be greater than PPC35.
1043 PPC43 is not in increasing positional order.
If non-zero, PPC43 must be greater than PPC39.
1047 PPC47 is not in increasing positional order.
If non-zero, PPC47 must be greater than PPC43.