Rockwell Automation 1771-QI,D17716.5.126 PLASTIC MOLD.MODULE User Manual
Page 5

Publication 1771-6.5.126– March 1998
Chapter 1
Chapter Contents
1–1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DYC – Dynamic Command Block
1–2
. . . . . . . . . . . . . . . . . . . . . . . . .
HDC – Hold Configuration Block
1–2
. . . . . . . . . . . . . . . . . . . . . . . . .
HPC – Pack/Hold Profile Block
1–3
. . . . . . . . . . . . . . . . . . . . . . . . . .
INC – Injection Configuration Block
1–4
. . . . . . . . . . . . . . . . . . . . . . .
IPC – Injection Profile Block
1–6
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
JGC – Jog Configuration Block
1–7
. . . . . . . . . . . . . . . . . . . . . . . . . .
MCC – Module Configuration Command Block
1–8
. . . . . . . . . . . . . . . .
PKC – Pack Configuration Block
1–19
. . . . . . . . . . . . . . . . . . . . . . . . .
PLC – Plastication Configuration Block
1–10
. . . . . . . . . . . . . . . . . . . . .
PPC – Plastication Profile Block
1–11
. . . . . . . . . . . . . . . . . . . . . . . . . .
PRC – Pre-decompression Configuration Block
1–12
. . . . . . . . . . . . . . .
PSC – Post-decompression Configuration Block
1–13
. . . . . . . . . . . . . .
PTC – Process Trace Configuration Block
1–14
. . . . . . . . . . . . . . . . . . .
RLC – Inject ERC Values Block
1–14
. . . . . . . . . . . . . . . . . . . . . . . . . .
HPS – Pack/Hold Profile Status Block
1–15
. . . . . . . . . . . . . . . . . . . . .
IPS – Injection Profile Status Block
1–16
. . . . . . . . . . . . . . . . . . . . . . . .
PPS – Plastication Profile Status Block
1–18
. . . . . . . . . . . . . . . . . . . . .
PTS – Process Trace Status Block
1–19
. . . . . . . . . . . . . . . . . . . . . . . .
RLS – Inject ERC Values Status Block
1–20
. . . . . . . . . . . . . . . . . . . . .
SYS – System Status Block
1–21
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 2
List of Command Blocks and Block ID codes
2–1
. . . . . . . . . . . . . . . . .
List of Data Words
2–1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engineering Units
2–2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Blocks Require I/O Configuration
2–2
. . . . . . . . . . . . . . . . . . . . . .
Data Blocks for System Control
2–3
. . . . . . . . . . . . . . . . . . . . . . . . . .
Data Blocks for Controlling Ram (Screw) Position
2–3
. . . . . . . . . . . . . .
DYC – Dynamic Command Block
3–4
. . . . . . . . . . . . . . . . . . . . . . . . .
Bit-mapped Control Words
2–4
. . . . . . . . . . . . . . . . . . . . . . . . . .
Direct Set-output Values
2–9
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Direct Set-output Ramp Rates
2–9
. . . . . . . . . . . . . . . . . . . . . . .
Table of Contents
Abbreviated Command
and Status Block
Command
Word/Bit Descriptions