Motorola Series Switch WS5100 User Manual
Motorola Computer Accessories
Table of contents
Document Outline
- Contents
- Overview
- 1.1 Hardware Overview
- 1.2 Software Overview
- 1.2.1 Infrastructure Features
- 1.2.1.1 Installation Feature
- 1.2.1.2 Licensing Support
- 1.2.1.3 Configuration Management
- 1.2.1.4 Diagnostics
- 1.2.1.5 Serviceability
- 1.2.1.6 Tracing / Logging
- 1.2.1.7 Process Monitor
- 1.2.1.8 Hardware Abstraction Layer and Drivers
- 1.2.1.9 Redundancy
- 1.2.1.10 Secure Network Time Protocol (SNTP)
- 1.2.1.11 Password Recovery
- 1.2.2 Wireless Switching
- 1.2.2.1 Physical Layer Features
- 1.2.2.2 Rate Limiting
- 1.2.2.3 Proxy-ARP
- 1.2.2.4 HotSpot / IP Redirect
- 1.2.2.5 IDM (Identity Driven Management)
- 1.2.2.6 Voice Prioritization
- 1.2.2.7 Self Healing
- 1.2.2.8 Wireless Capacity
- 1.2.2.9 AP and MU Load Balancing
- 1.2.2.10 Wireless Roaming
- 1.2.2.11 Power Save Polling
- 1.2.2.12 QoS
- 1.2.2.13 Wireless Layer 2 Switching
- 1.2.2.14 Automatic Channel Selection
- 1.2.2.15 WMM-Unscheduled APSD
- 1.2.3 Wired Switching
- 1.2.4 Management Features
- 1.2.5 Security Features
- 1.2.5.1 Encryption and Authentication
- 1.2.5.2 MU Authentication
- 1.2.5.3 Secure Beacon
- 1.2.5.4 MU to MU Allow
- 1.2.5.5 MU to MU Disallow
- 1.2.5.6 Switch-to-Wired
- 1.2.5.7 802.1x Authentication
- 1.2.5.8 IEEE 802.1AB LLDP
- 1.2.5.9 WIPS
- 1.2.5.10 Rogue AP Detection
- 1.2.5.11 ACLs
- 1.2.5.12 Local Radius Server
- 1.2.5.13 IPSec VPN
- 1.2.5.14 NAT
- 1.2.5.15 Certificate Management
- 1.2.6 Access Port Support
- 1.2.1 Infrastructure Features
- Switch Web UI Access and Image Upgrades
- Switch Information
- Network Setup
- 4.1 Displaying the Network Interface
- 4.2 Viewing Network IP Information
- 4.3 Viewing and Configuring Layer 2 Virtual LANs
- 4.4 Configuring Switch Virtual Interfaces
- 4.5 Viewing and Configuring Switch WLANs
- 4.6 Viewing Associated MU Details
- 4.7 Viewing Access Port Information
- 4.8 Viewing Access Port Adoption Defaults
- 4.9 Viewing Access Port Status
- Switch Services
- 5.1 Displaying the Services Interface
- 5.2 DHCP Server Settings
- 5.3 Configuring Secure NTP
- 5.4 Configuring Switch Redundancy
- 5.5 Layer 3 Mobility
- 5.6 Configuring GRE Tunnels
- 5.7 Configuring Self Healing
- 5.8 Configuring Switch Discovery
- Switch Security
- 6.1 Displaying the Main Security Interface
- 6.2 AP Intrusion Detection
- 6.3 MU Intrusion Detection
- 6.4 Configuring Wireless Filters
- 6.5 Configuring ACLs
- 6.6 Configuring NAT Information
- 6.7 Configuring IKE Settings
- 6.8 Configuring IPSec VPN
- 6.9 Configuring the Radius Server
- 6.10 Creating Server Certificates
- Switch Management
- Diagnostics