Basler Electric BE1-11t - Manual (Page 384)

372 9424200995 Rev H
Step
Pickup
Setting
Low Actual
Pickup
High Low *
Actual
Dropout
High *
Pass/Fail
I2 IA I2 IA I2 IA I2 IA I2 IA
6
0.5
(5A CT)
1.5 0.42 1.26 0.57 1.71 0.46 1.38 0.49 1.47 P / F
7
5.0
(5A CT)
15.0 4.85 14.55 5.15 15.45 4.65 13.95 4.95 14.85 P / F
7
9.0
(5A CT)
27.0 8.73 26.19 9.27 27.81 8.37 25.11 8.91 26.73 P / F
6
0.1
(1A CT)
0.3 0.08 0.24 0.11 0.33 0.093 0.279 0.099 0.297 P / F
7
1.0
(1A CT)
3.0 0.97 2.91 1.03 3.09 0.93 2.79 0.99 2.97 P / F
7
1.8
(1A CT)
5.4 1.74 5.22 1.85 5.55 1.67 5.01 1.78 5.34 P / F
* Dropout range is calculated from the pickup setting and may need adjusted based on actual pickup.
Timing Verification (I2 Mode)
Time Delay Range = 0 to 60,000 ms
Timing Accuracy =
±0.5% or ±½ cycle, whichever is greater + 3 cycles max for currents 1.5 x pickup
Step Time Delay Setting Low Actual Timing High Pass/Fail
4 2,000 ms 1,942 ms 2,058 ms P / F
5 5,000 ms 4,927 ms 5,073 ms P / F
5 10,000 ms 9,902 ms 10,098 ms P / F
Pickup Verification (IG Mode)
Pickup Setting Range = 0.5 to 150 A for 5A sensing
0.1 to 30 A for 1A sensing
0.01 to 7.5 for SEF
Pickup Accuracy =
±2% or ±50 mA, whichever is greater for 5A sensing
±2% or ±10 mA, whichever is greater for 1A sensing
±2.5% or ±2.5 mA, whichever is greater for SEF
Dropout should occur between 93-99% of the actual pickup value.
Step Pickup Setting Low Actual Pickup High Low
*
Actual Dropout High
*
Pass/Fail
6 0.5 A (5A CT) 0.45 A 0.55 A 0.465 A 0.495 A P / F
7 5.0 A (5A CT) 4.9 A 5.1 A 4.65 A 4.95 A P / F
7 20.0 A (5A CT) 20.6 A 20.4 A 18.6 A 19.8 A P / F
6 0.1 A (1A CT) 0.09 A 0.11 A 0.093 A 0.099 A P / F
7 1.0 A (1A CT) 0.98 A 1.02 A 0.93 A 0.99 A P / F
7 2.0 A (1A CT) 1.96 A 2.04 A 1.86 A 1.98 A P / F
6 0.1 A (SEF) 0.09 A 0.11 A 0.093 A 0.099 A P / F
7 1.0 A (SEF) 0.85 A 1.15 A 0.93 A 0.99 A P / F
7 2.0 A (SEF) 1.95 A 2.05 A 1.86 A 1.98 A P / F
* Dropout range is calculated from the pickup setting and may need adjusted based on actual pickup.
Instantaneous Overcurrent (50) Test BE1-11t