Rockwell Automation FlexPak 3000 Digital DC Drive Version 4.3 - Manual (Page 190)

Index-4 FlexPak 3000 DC Drive Software Reference
NETW OUT REG 3 SELECT (P.904), 10-5
NETW REGISTER MAP SEL (P.914), 10-8
NETW TYPE & VERSION (P.909), 10-6
network, 10-1
settings, 10-2
speed reference, 4-8
NETWORK BAUD RATE (P.912), 10-7
NETWORK KIT (P.796), 10-6
NOMINAL AC LINE FREQ (P.306), 3-2
NOMINAL AC LINE VOLTS (P.307), 3-2
NORMALIZED INERTIA (P.222), 6-3
O
ocl
block diagram, 9-1
enable logic block diagram, 9-2
feedback path setup, 9-9
forward path, 9-6
reference path, 9-4
reference signal rounding block diagram, 9-6
signal processing, 9-4
OCL , 9-1
OCL ENABLE (P.849), 9-4
OCL FEEDBACK (P.847), 9-9
OCL FEEDBACK SELECT (P.804), 9-10
OCL LEADLAG LOW FREQ (P.806), 9-10
OCL LEADLAG RATIO (P.807), 9-11
OCL LEADLAG SELECT (P.805), 9-11
OCL OUTPUT (P.848), 9-7
OCL PI LEAD FREQ (P.809), 9-7
OCL PI NEGATIVE LIMIT (P.811), 9-7
OCL PI POSITIVE LIMIT (P.810), 9-7
OCL PI PROP GAIN (P.808), 9-8
OCL PROP TRIM SELECT (P.813), 9-8
OCL RAMP OUTPUT (P.846), 9-4
OCL REF RAMP TIME (P.802), 9-5
OCL REF REGISTER (P.801), 9-6
OCL REF ROUNDING (P.803), 9-6
OCL REFERENCE (P.845), 9-5
OCL REFERENCE SELECT (P.800), 9-5
OCL TRIM RANGE (P.812), 9-8
OCL TYPE 3 POSN REG EN (P.814), 9-11
OIM speed reference, 4-23
OPEN SCR SENSITIVITY (P.600), 13-15
OPEN SCR TRIP THRESH (P.601), 13-15
outer control loop See OCL
P
PHASE FIRE TEST DELTA (P.309), 13-18
PHASE FIRE TST BRIDGE (P.310), 13-18
PHASE LOSS DETECTION EN (P.609), 13-22
PLL MAXIMUM ERROR (P.308), 13-13
POS CURRENT LIM SEL (P.223), 5-16
POSITIVE CURRENT LIM (P.005), 5-17
POWER UNIT TYPE (P.795), 13-23
preset speed
block diagram, 4-11
references, 4-11
PRESET SPEED 1 (P.117) PRESET SPEED 2 (P.118),
4-12
PRESET SPEED 3 (P.119), 4-12
pulse encoder feedback, 5-9
block, 5-9
PULSE TACH FEEDBACK (P.292), 5-9
PULSE TACH PPR (P.207), 5-9
PULSE TACH QUADRATURE (P.208), 5-10
PULSE TACHOMETER KIT (P.798), 5-10
pulse tachometer See pulse encoder
R
RAMP STOP DECEL TIME (P.018), 4-20
ramp stop sequencing, 2-3
reference
affect on control source, 4-2
regulator, 13-23
REGULATOR SW VERSION (P.794), 13-23
REVERSE DISABLE (P.015), 4-21
run
mode, 2-2
sequencing, 2-2
S
scr
adjusting sensitivity, 13-14
diagnostics, 13-14
load during normal operation, 13-14
load
SCR s fail to turn on, 13-15
S - CURVE ROUNDING (P.014), 4-21
SELF TUNE BRIDGE (P.220), 3-3
SELF TUNE FIELD RANGE (P.218), 3-3
SELF TUNE STABILITY (P.219), 3-4
serial speed reference, 4-8
SPD LEADLAG LOW FREQ (P.214), 5-11
SPD LEADLAG RATIO (P.213), 5-12
SPD LEADLAG SELECT (P.216), 5-12
SPD LOOP ERROR (P.297), 5-12
SPD LOOP FEEDBACK (P.296), 5-12
SPD LOOP LAG BYPASS (P.217), 5-13
SPD LOOP LAG FREQ (P.215), 5-13
SPD LOOP LAG OUTPUT (P.298), 5-13