Rockwell Automation FlexPak 3000 Digital DC Drive Version 4.3 - Manual (Page 187)

Index Index-1
I
NDEX
A
AC
analog tachometer feedback block diagram,
5-6
checking line period and voltage, 13-22
line parameter configuration, 3-2
AC LINE PERIOD (P.393), 13-22
AC LINE VOLTAGE (P.392), 13-22
AC LINE VOLTAGE HIGH alarm, 3-2
AC LINE VOLTAGE LOW alarm, 3-2
ACCELERATION TIME (P.001), 4-18
alarm codes, 13-9 to 13-11
AMX NETW REF SELECT (P.911), 10-8
analog
auto speed reference, 4-4
inputs
block diagram, 11-5
setting parameters, 11-5
manual speed reference, 4-6
outputs
block diagram, 11-8
setting parameters, 11-8
ANALOG AUTO REFERENCE (P.188), 4-4
ANALOG MAN REFERENCE (P.192), 4-6
ANALOG MAN TRIM REF (P.194), 4-14
ANALOG TACH FEEDBACK (P.291), 5-6
ANALOG TACH GAIN ADJ (P.201), 5-7
ANALOG TACH ZERO ADJ (P.202), 5-7
ANLG AUTO GAIN ADJ (P.101), 4-5
ANLG AUTO SIGNAL TYPE (P.100), 4-5
ANLG AUTO ZERO ADJ (P.102), 4-5
ANLG IN 1 (P.492), 11-5
ANLG IN 1 GAIN ADJ (P.415), 11-6
ANLG IN 1 SIG TYPE (P.413), 11-6
ANLG IN 1 ZERO ADJ (P.414), 11-6
ANLG IN 2 (P.493), 11-7
ANLG IN 2 GAIN ADJ (P.417), 11-7
ANLG IN 2 ZERO ADJ (P.416), 11-7
ANLG MAN REF GAIN ADJ (P.104), 4-7
ANLG MAN REF ZERO ADJ (P.105), 4-7
ANLG OUT 1 GAIN ADJ (P.420), 11-8
ANLG OUT 1 SELECT (P.418), 11-9
ANLG OUT 1 SIG TYPE (P.419), 11-9
ANLG OUT 2 GAIN ADJ (P.422), 11-9
ANLG OUT 2 SELECT (P.421), 11-10
ANLG TACH VOLTS /1000 (P.203), 5-7
ARM VOLTAGE GAIN ADJ (P.204), 5-4
ARM VOLTAGE ZERO ADJ (P.205), 5-4
armature
current feedback scaling, 6-6
phase fire test, 13-16
voltage block diagram, 5-3
ARMATURE BRIDGE POL (P.394), 6-9
ARMATURE DELTA (P.399), 6-10
ARMATURE VOLTAGE (P.289), 5-4
assistance, 1-2
auto mode, 4-2
AUTO MODE MIN BYPASS (P.111), 4-18
AUTO MODE RAMP BYPASS (P.112), 4-19
AUTO REFERENCE SELECT (P.103), 4-6
automatic field weakening, 8-8
AutoMax Network, 10-1
kit parameters, 10-8
C
cml
block diagram, 6-6
forward path, 6-9
reference path diagram, 6-1
reference selection and conditioning, 6-3
CML , 6-1
CML ERROR (P.398), 6-10
CML FEEDBACK (P.397), 6-7
CML FEEDBACK GAIN ADJ (P.300), 6-7
CML PI LEAD FREQUENCY (P.302), 6-10
CML PI PROP GAIN (P.301), 6-10
CML REF LIMIT SELECT (P.311), 6-3
CML REF RATE LIMIT (P.303), 6-4
CML REFERENCE (P.396), 6-4
CNI PROGRAM RUN MODE (P.915), 10-9
coast/DB stop sequencing, 2-3