Lenze EPM−T9XX Modular system - Manual (Page 538)

Total index
15
Appendix
15.3
L
15.3−6 EDSPM−TXXX−9.0−11/2009
Connection
− CANopen, 4.1−1 , 4.2−1 , 5.1−2 , 5.2−2 , 5.3−2 , 5.4−2
Pin assignment at the module, 5.1−2 , 5.2−2 , 5.3−2 ,
5.4−2
− Sub−D socket at the PROFIBUS gateway, 4.3−1
− Sub−D socket on PROFIBUS Gateway, 4.1−1 , 4.2−1 ,
7.4−1
− Sub−D socket on the PROFIBUS Gateway, 4.4−2 ,
7.5−3
− System bus (CAN), 4.1−1 , 4.2−1 , 5.1−2 , 5.2−2 ,
5.3−2 , 5.4−2
Pin assignment at the module, 5.1−2 , 5.2−2 , 5.3−2 ,
5.4−2
Consistent parameter data, 10.5−7
D
Definition of notes used, 2.1−1
Definitions, Terms, 15.2−1
Description
− 16xdig. I/O compact (single−wire conductor), 5.2−1
− 16xdig. I/O compact (three−wire conductor), 5.3−1
− 16xdigital input, 4.6−1
− 16xdigital output 0.5A, 4.8−1
− 16xdigital output 1A, 4.10−1
− 1xcounter/16xdigital input, 4.23−1
− 2/4xcounter, 4.21−1
− 32xdig. I/O compact, 5.4−1
− 4xanalog input, 4.14−1
− 4xanalog input / output, 4.20−1
− 4xanalog input ±10V, 4.15−1
− 4xanalog input ±20mA, 4.16−1
− 4xanalog output, 4.17−1
− 4xanalog output ±10V, 4.18−1 , 4.19−1
− 4xrelay, 4.12−1
− 8xdig. I/O compact, 5.1−1
− 8xdigital input, 4.5−1
− 8xdigital input / output, 4.13−1
− 8xdigital output 0.5A, 4.7−1
− 8xdigital output 1A, 4.9−1
− 8xdigital output 2A, 4.11−1
− CAN gateway, 4.1−1
− CAN GatewayECO, 4.2−1
− PROFIBUS Gateway, 4.3−1
− PROFIBUS GatewayECO, 4.4−1
− SSI interface, 4.22−1
− Terminal module, 4.24−1
Device address setting, 4.2−2
Device protection, 3.1−1
Device status
− of the heartbeat producer, 8.7−2 , 9.7−2
− of the I/O system IP20, 8.6−2 , 9.6−2
− of the slave, 8.6−2 , 9.6−2
Diagnostic data, Transmission with analog modules,
12.3−6
Diagnostics, Elapsed time and running time meter,
10.6−1
Digital inputs, Status request, 8.10−3 , 9.10−3
Digital modules
− 16xdigital input, Parameter setting, 12.2−1
− 16xdigital output, Parameter setting, 12.2−1
− 8xdigital input, Parameter setting, 12.2−1
− 8xdigital input / output, Parameter setting, 12.2−1
− 8xdigital output, Parameter setting, 12.2−1
Digital outputs, Status request, 8.10−4 , 9.10−4
Dimensions
− Compact system, 6.2−1
− Modular system, 6.1−1
Disassembly, Module, 6.1−3
disassembly, Module, 6.2−2
E
Elapsed time and running time meter, 10.6−1
Electrical installation, 7.1
− Communication connection, 7.4−1 , 7.5−3
Electrical isolation, 3.1−1
EMC, 3.1−1
− Assembly, 7.1−1
− Earthing, 7.1−1
− Shielding, 7.1−1
Emergency telegram, 8.10−2 , 9.10−2
Error Response, 8.4−2 , 9.4−2
F
Fault indications
− at 8xdig. I/O compact, 5.1−4 , 5.2−4 , 5.3−4 , 5.4−4
− at CAN gateway, 4.1−3 , 4.2−3
Fault messages, 14.1−1
− on the CAN Gateway, 4.3−2 , 4.4−2