TA Triumph-Adler DC 2023 - Manual (Page 109)

4-37
Section 4 Other Features of this Fax
14. Enter the subaddress you want to use for this F-Code Based
Transmission.
* The subaddress can be up to 20 digits in length and can
include any combination of the numerals 0 - 9.
15. Press the Enter key.
16. If necessary, enter the predetermined F-Code password.
* The password can be up to 20 digits in length and can include
any combination of the numerals 0 - 9 and the symbols “ ” and
“#”. You do not have to enter an F-Code password here if you
agree in advance with the destination party not to use one.
* If you DO NOT need to enter an F-Code password, proceed to
step 17.
17. Press the Enter key.
* If the fax number you entered has already been registered for
this operation or too many numbers were entered, an error
message will appear in the message display. In this case,
press the Enter key and the message display will return to a
display that allows you to enter the destination fax number again.
18. Select whether or not you want to continue entering other
destination fax numbers.
> If you DO want to enter more fax numbers, return to step 12 on
page 4-36.
> If you are finished entering fax numbers, proceed to step 19.
19. Press the Enter key.
20. Enter a name for the program.
* The program name can be up to 20 characters in length.
(Refer to “Entering characters”, page 1-28.)
21. Press the Enter key. The entered information will become
registered under the designated program key.
> If you want to continue registering other program keys,
return to step 4, page 4-35.
> If you are finished registering program keys, press the Reset
key. The operation panel will return to the initial mode settings.
3A180100A
3A1/FaxSystem(A)/MCE-Eng
/ 164
C. Polling Reception (Continued from step 5, page 4-35)
6. Use the cursor up or the cursor down key to select “RX polling”.
7. Press the Enter key.
8. Use the cursor up or the cursor down key to select whether or not
you want to designate a time for the reception to begin.
> If you want to designate a time for the reception to begin,
select “On” and proceed to step 9.
> If you want to have the reception begin immediately after the
program key is pressed, select “Off” and proceed to step 11.
9. Press the Enter key.
10. Use the keypad to enter the desired time for the reception to
begin.
* If you want to reset the displayed time to “00:00”, simply press
the Stop/Clear key.
11. Press the Enter key.
12. Enter the fax number of a transmitting party.
* You can enter the fax number using the keypad, abbreviated
numbers, one-touch keys, group dial keys or the directory.
Chain dial keys can be used as well.
If you enter the fax number using an abbreviated number or
one-touch key that is already designated for F-Code Based
Communication, you can skip steps 13 through 16.
13. If you want to designate the communication for this fax number
as an F-Code Based Reception, press the SUBADDRESS key.
> If you pressed the SUBADDRESS key, proceed to step 14.
> If you DID NOT press the SUBADDRESS key, proceed to
step 17, page 4-38.
Subaddress:
6635
20 digits
Enter subaddress numbers
Password:
20 digits
Enter your password
Password:
3856
20 digits
Enter your password
v :
Enter fax number
M.S.G.
Enter program name
Program:05:Select mode
Send
Broadcast
➪ RX polling
Delayed comm.:
➪ On
Off
TX time:17:00
Enter transmission time
v :
Enter fax number
04/OtherF-3/3A1/MCE/Eng.q 23-12-1999 14:01 Page 4-37