FEC FUSIONE-HS-2 - Manual (Page 167)

FUSION Operations Manual
8.3 Replacements
WARNING: DO NOT CONNECT OR DISCONNECT CABLES OR OTHER SYSTEM
COMPONENTS WITH POWER APPLIED. FOLLOW LOCKOUT/TAGOUT AND
OTHER APPLICABLE SAFETY PRECAUTIONS WHEN CONNECTING OR
DISCONNECTING CABLING, WIRING, AND EQUIPMENT.
NOTE: When replacing the
gured with the same Hardware and the same Firmware version as the unit being replaced.
(Controller Unit displays the
lected. Version will sh
8.3.1 Controller Unit Replacement (No Partial Replacement)
All tools operate from one model of Controller (HFC
ing replaced with another, it is important to verify that
unit being removed.
1.
Verify the controller power is off. Ensure all cables connected to the
(for ease of reconnection).
2. Disconnect all cables from the rear (& front if applicable)
I/O terminal on the controller and to avoid removing all the I/O wires, you may simply disassemble the
terminal block from the controller using the top and bottom screws holding the terminal block to the
controller, and reassemble the terminal block to the new controller.
3. Turn the controller on the cover hinges 90 degrees and
4. Verify the new controller
Section 4.10.
5. Verify the SAN Units have the same configuration (hardware and software).
6. Install the new controller
7. Apply power and confirm operation
Power On Self Test (POST)
The new Controller will require reentry of the preset data. Refer to Chapters 6
and 7.
FUSION Operations Manual Chapter 8: Maintenance and Inspection (
Page 8-7
DO NOT CONNECT OR DISCONNECT CABLES OR OTHER SYSTEM
COMPONENTS WITH POWER APPLIED. FOLLOW LOCKOUT/TAGOUT AND
OTHER APPLICABLE SAFETY PRECAUTIONS WHEN CONNECTING OR
DISCONNECTING CABLING, WIRING, AND EQUIPMENT.
When replacing the FUSION System Controller unit, ensure that the new unit is conf
gured with the same Hardware and the same Firmware version as the unit being replaced.
displays the Firmware Version number when “WORK” 00 D
will show in the Data Display. ie. 1.02)
Unit Replacement (No Partial Replacement)
All tools operate from one model of Controller (HFC-EC-16). When one
ing replaced with another, it is important to verify that the new unit is set
unit being removed.
power is off. Ensure all cables connected to the controller
nnect all cables from the rear (& front if applicable) of the unit. If wires are connected to the
I/O terminal on the controller and to avoid removing all the I/O wires, you may simply disassemble the
terminal block from the controller using the top and bottom screws holding the terminal block to the
emble the terminal block to the new controller.
Turn the controller on the cover hinges 90 degrees and Lift up on the controller
controller unit dip switches are set the same as the unit being replaced
Verify the SAN Units have the same configuration (hardware and software).
controller in reverse order of removal.
and confirm operation. (After approximately 5 seconds, the controller
Self Test (POST)).
will require reentry of the preset data. Refer to Chapters 6
Chapter 8: Maintenance and Inspection (Rev. 2)
DO NOT CONNECT OR DISCONNECT CABLES OR OTHER SYSTEM
COMPONENTS WITH POWER APPLIED. FOLLOW LOCKOUT/TAGOUT AND
OTHER APPLICABLE SAFETY PRECAUTIONS WHEN CONNECTING OR
unit, ensure that the new unit is confi-
gured with the same Hardware and the same Firmware version as the unit being replaced.
when “WORK” 00 D-NO 01 is se-
When one Controller unit is be-
is set-up identical to the
controller are clearly marked
If wires are connected to the
I/O terminal on the controller and to avoid removing all the I/O wires, you may simply disassemble the
terminal block from the controller using the top and bottom screws holding the terminal block to the
on the controller unit to remove.
same as the unit being replaced. Refer to
controller will finalize the
will require reentry of the preset data. Refer to Chapters 6