Comtech EF Data VMS v3.12.x Vipersat - Manual (Page 18)

xii VMS User Guide
MN/22156, rev 12
Modem. . . . . . . . . . . . . . . . . . . . . . . . 3-118
Chapter 4 Figures
Figure 4-1 Parameter View and Modem Command
Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Figure 4-2 Parameter Editor, CDM-800 Example.
4-6
Figure 4-3 Information Help Feature Example . 4-7
Figure 4-4 Tree Menus, Series800 Modems . . 4-9
Figure 4-5 Modem Configure Command, ViperView
4-10
Figure 4-6 General Parameters dialog, CDM-800
4-11
Figure 4-7 External Reference Frequency Pull-
Down Menu, CDM-800 . . . . . . . . . . . . 4-13
Figure 4-8 Network Interfaces dialog, CDM-800 .
4-14
Figure 4-9 Hub Routing Table dialog, CDM-800 .
4-17
Figure 4-10 Additional Routing Table Columns . .
4-18
Figure 4-11 Default Route for Remote, CDM-840
4-18
Figure 4-12 Route Properties dialog, CDM-800 . .
4-19
Figure 4-13 Editing Table Entries, Alternative
Method. . . . . . . . . . . . . . . . . . . . . . . . . 4-20
Figure 4-14 Network ARP dialog, CDM-800. . 4-21
Figure 4-15 ARP Properties dialog. . . . . . . . . 4-21
Figure 4-16 Wide Area Network dialog, CDM-840
4-22
Figure 4-17 Compression Refresh Rates dialog,
CDM-800 . . . . . . . . . . . . . . . . . . . . . . . 4-23
Figure 4-18 Quality of Service dialog, CDM-840 .
4-25
Figure 4-19 Quality of Service Groups dialog. 4-29
Figure 4-20 QoS Group Properties dialog . . . 4-30
Figure 4-21 QoS Rule Properties dialog, CDM-800
4-33
Figure 4-22 Quality of Service Rules Table dialog,
CDM-840 . . . . . . . . . . . . . . . . . . . . . . . 4-36
Figure 4-23 QoS Rule Properties dialog, CDM-840
4-36
Figure 4-24 Receive Transmit Inhibit dialog, CDM-
840. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-37
Figure 4-25 Link Adaptation Configuration, CDM-
840. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-38
Figure 4-26 ACM Link Adaptation dialog, CDD-880
4-39
Figure 4-27 Entry Channel Configuration dialog,
CDD-880 . . . . . . . . . . . . . . . . . . . . . . .4-40
Figure 4-28 Entry Channel Configuration, CDM-
840 . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-43
Figure 4-29 BERT dialog, CDM-840. . . . . . . .4-45
Figure 4-30 Internet Group Management dialog,
CDM-840 . . . . . . . . . . . . . . . . . . . . . . .4-47
Figure 4-31 Dynamic Host Relay dialog, CDM-840
4-49
Figure 4-32 Network Management dialog, CDM-
800 . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-50
Figure 4-33 Load Switching dialog, CDM-840 4-52
Figure 4-34 ToS Switching dialog, CDM-840 .4-54
Figure 4-35 ToS Rule dialog, CDM-840 . . . . .4-54
Figure 4-36 E1 dialog, CDM-840 . . . . . . . . . .4-56
Figure 4-37 E1 Timeslots dialog, CDM-840 . .4-57
Figure 4-38 DVB Modulator dialog, CDM-800 4-58
Figure 4-39 VersaFEC Modulator dialog, CDM-840
4-59
Figure 4-40 Return Path ModCod, Remote Site
Properties. . . . . . . . . . . . . . . . . . . . . . .4-64
Figure 4-41 DVB Demodulator dialog, CDM-840 .
4-65
Figure 4-42 VersaFEC Demodulator dialog, CDD-
880 . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-67
Figure 4-43 Block Down Converter dialog, CDM-
840 . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-69
Figure 4-44 Block Up Converter dialog, CDM-840
4-70
Chapter 5 Figures
Figure 5-1 ROSS Status View, ViperView . . . .5-2
Figure 5-2 ROSS Command Menu. . . . . . . . . .5-4
Figure 5-3 ROSS Service Areas List . . . . . . . .5-6
Figure 5-4 Service Bounds dialog. . . . . . . . . . .5-6
Figure 5-5 ROSS Event Log . . . . . . . . . . . . . . .5-7
Figure 5-6 ROSS General Properties . . . . . . . .5-8
Figure 5-7 ROSS Stored Configurations . . . . .5-9
Figure 5-8 Parameter Editor, ROSS Example 5-11
Figure 5-9 Network Settings dialog, ROSS . .5-12
Figure 5-10 Modem Settings dialog, ROSS . .5-13
Figure 5-11 Management Settings dialog, ROSS.
5-14
Figure 5-12 ACU Settings dialog, ROSS . . . .5-15
Figure 5-13 Tracking Settings dialog, ROSS .5-16