AMETEK i Series - Manual (Page 11)

i Series / iX Series vii
List of Figures
Figure 3-1: The 5001iX Power Source ................................................................................................................ 15
Figure 3-2: RS232C Cable for PC Connection wiring diagram. .......................................................................... 21
Figure 3-3: Function Strobe Connection. ............................................................................................................ 22
Figure 3-4: Function Strobe / Trigger Output Accessory. .................................................................................... 22
Figure 3-5: Rear Panel View for the 3001i/3001iX ............................................................................................. 24
Figure 3-6: Rear Panel View for the 5001i/5001iX ............................................................................................. 25
Figure 3-7: Connection For Single Power Source (5001iX/i, 3001iX/i) ................................................................ 28
Figure 3-8: Functional Test Setup ....................................................................................................................... 29
Figure 3-9: Single Phase 10000 VA System (10001iX/i) .................................................................................... 30
Figure 3-10: Three Phase 15000 VA System (15003iX/i-LK Three Controllers) ................................................ 31
Figure 3-11: Single Phase 15000 VA System (15001iX/i) .................................................................................. 32
Figure 3-12: Three-Phase 15000 VA system (15003iX/i - One Controller) ........................................................ 33
Figure 3-13: Connection With MODE Option ..................................................................................................... 34
Figure 3-14: Two Phase 10000 VA System (10002i-LK Two Controllers) ......................................................... 35
Figure 3-15: Three-Phase 9000 VA System (9003iX/i – One Controller) ........................................................... 36
Figure 4-1: Shuttle Knob ..................................................................................................................................... 38
Figure 4-2: FUNCTION keypad .......................................................................................................................... 39
Figure 4-3: Entering value from decimal keypad ................................................................................................ 40
Figure 4-4: Cursor UP key movement ................................................................................................................ 41
Figure 4-5: Cursor DOWN key movement ......................................................................................................... 41
Figure 4-6: Main Menu 1 screen ......................................................................................................................... 42
Figure 4-7: Menu 1 through 3 ............................................................................................................................. 42
Figure 4-8: PROGRAM Menu ............................................................................................................................. 46
Figure 4-9: MEASUREMENTS Screen, single phase and three phase modes .................................................. 48
Figure 4-10: HARMONICS/TRACE ANALYSIS screen ...................................................................................... 50
Figure 4-11: TRANSIENTS menu ...................................................................................................................... 53
Figure 4-12: VOLTAGE SURGE/SAG SETUP screen ....................................................................................... 54
Figure 4-13: VOLTAGE SWEEP/STEP SETUP screen ..................................................................................... 56
Figure 4-14: FREQUENCY SWEEP/STEP SETUP screen ................................................................................ 58
Figure 4-15: VOLTAGE/FREQUENCY SWEEP/STEP SETUP screen .............................................................. 59
Figure 4-16: START/VIEW TRANSIENT SEQUENCE screen ............................................................................ 60
Figure 4-17: WAVEFORMS menu ..................................................................................................................... 61
Figure 4-18: APPLICATIONS menu ................................................................................................................... 64
Figure 4-19: SETUP REGISTERS menu ............................................................................................................ 65
Figure 4-20: UTILITY menu ................................................................................................................................ 66
Figure 4-21: GPIB/RS232 SETUP menu ............................................................................................................ 68
Figure 4-22: VOLTAGE/CURRENT CONTROL SETUP menu ........................................................................... 69
Figure 4-23: INITIAL SETUP menus ................................................................................................................... 70
Figure 4-24:LIMIT SETUP menu ......................................................................................................................... 72
Figure 4-25: OUTPUT IMPEDANCE menu ......................................................................................................... 74
Figure 4-26: MEASUREMENT CAL FACTORS menu ........................................................................................ 75
Figure 4-27: OUTPUT CAL FACTORS menu ..................................................................................................... 76
Figure 4-28: Selecting a waveform ...................................................................................................................... 78
Figure 4-29: Selecting waveforms for single phase or all phases ...................................................................... 79
Figure 4-30: Custom waveform creation with GUI program ................................................................................ 80
Figure 4-31: Waveform crest factor affects max. rms voltage ............................................................................. 81
Figure 4-32: Waveform frequency domain view mode ....................................................................................... 82
Figure 4-33: Scrolling through tabular FFT data ................................................................................................ 86
Figure 4-34: Scrolling through bar chart FFT data ............................................................................................. 86
Figure 4-35: Scrolling through acquired waveform data ..................................................................................... 88
Figure 4-36: SET VOLT trigger source acquisition ............................................................................................. 90
Figure 4-37: Positive trigger delay (Post trigger data) ........................................................................................ 92
Figure 4-38: Negative trigger delay (Pre-trigger data) ........................................................................................ 93
Figure 4-39: Pulse Transients ............................................................................................................................ 95
Figure 4-40: List Transients ................................................................................................................................ 96
Figure 4-41: Switching waveforms in a transient list .......................................................................................... 99
Figure 4-42: START/VIEW TRANSIENT SEQUENCE menu ........................................................................... 100
Figure 5-1: AC Power System Block Diagram .................................................................................................. 101
Figure 5-2: Power Source Module Block Diagram ........................................................................................... 104
Figure 5-3: 5001i Internal Layout ..................................................................................................................... 107
Figure 5-4: Logic Board LED's .......................................................................................................................... 108