KEYENCE SR-750 Series - Manual (Page 20)

20 E SR-750 UM
3-10
Batch Setting Code
This section describes the quick setup code.
Quick Setup Code
Users can print the settings specified with AutoID Network Navigator as 2D code
and read the code with the SR-750 Series to change all the settings at once. When
printing the quick setup code, use the AutoID Network Navigator quick setup code
printing function.
Since the settings of the SR-750 Series can be changed by reading the quick setup
code, you can easily change the settings even in a location where a computer
cannot be used.
„ Print image
Point When reading the quick setup code with the high-resolution type
unit (SR-750HA), you must use a printer with high print quality.
When a printer with low print quality is used, the cells in the 2D
code may bleed and become unreadable.
How to read quick setup codes
Use one of the following methods to read the quick setup code
„ Reading the quick setup code using the TUNE button
1
Press and hold the TUNE button on the SR-750 Series for at least 4
seconds.
When the quick setup code reading operation starts, "C" and "O" are displayed
alternately on the multiple LED indicator of the SR-750 main unit.
2
Read the quick setup code.
According to the code reading status, values displayed on the multiple LED
indicator of the SR-750 main unit change.
3
When all quick setup codes are read, "d" is displayed on the multiple
LED indicator of the SR-750 main unit.
4
Press the TUNE button once briefly to finish the quick setup code
reading operation.
• While reading the quick setup code, the TRG BUSY and MODE BUSY
outputs turn ON.
• To cancel the quick setup code reading operation, press the TUNE button
once briefly.
When "F" is displayed on the multiple LED display, press the TUNE button
once briefly again.
„ Sending the quick setup code reading commands
Send the quick setup code reading command (RCON) to read the quick setup
code.
1
Send the "RCON" command from the control device.
When the SR-750 Series receives the command normally, it returns "OK,
RCON", and "C" and "0" are displayed alternately on the multiple LED indicator
of the SR-750 main unit.
2
Read the quick setup code.
According to the code reading status, values displayed on the multiple LED
indicator of the SR-750 main unit change.
3
When all quick setup codes are read, "d" is displayed on the multiple
LED indicator of the SR-750 main unit.
4
Send the "RCOFF" command from the control device.
When the SR-750 Series receives the command normally, it returns "OK,
RCOFF", and the quick setup code reading operation finishes. (After the setting
is reflected, "d" on the multiple LED goes off.)
• While reading the quick setup code, the TRG BUSY and MODE BUSY
outputs turn ON.
• To cancel the quick setup code reading operation, send the "RCOFF"
command.
3-11
Code quality verification
function
This section describes the Code quality verification function.
Code quality verification function for the SR-750 Series
The Code quality verification function evaluates the level (High/Low) of total grade
based on the verification result output and the set threshold by verifying the 2D
code scanned with the SR-750 Series according to the marking quality evaluation
specified by a third-party institution.
The SR-750 Series provides the following 2D code verifications according to the
Code quality verification standards.
Important Note that this Code quality verification function is designed to
evaluate marking quality of the standards-compliant 2D codes of
the images scanned with the SR-750 Series, but cannot be used as
an official 2D code verification device.
Reference When you select ISO/IEC15415, you can perform code quality
verification of standalone PDF 417 and Micro PDF codes. For
information on the verification items, see
"Code Verification of
Japanese Pharmaceutical Drugs" in the "SR-750 Series Additional
Functions Manual."
Standards Description
ISO/IEC15415
This is the 2D code marking quality evaluation standard
established by International Organization for Standardization.
This is mainly used to evaluate 2D codes printed on labels.
ISO/IEC TR 29158
(AIM DPM-1-2006)
This is the DPM (Direct Part Marking) 2D code marking quality
evaluation standard established by Automatic Identification
Manufacturers.
This is based on ISO/IEC15415.
This was also standardized by International Organization for
Standardization in 2011.
SAE AS9132
This is the DataMatrix code marking quality evaluation
standard established by SAE (Society of Automotive
Engineers) and used by the aerospace industry.
SEMI T10-0701
This is the DataMatrix code marking quality evaluation
standard established by SEMI (Semiconductor Equipment and
Materials International) and printed on semiconductor-related
materials.