Rockwell Automation 1758-RTU202 DataSite Software User Manual FRN 1.2 User Manual
Page 7

Publication 1758-UM002D-EN-P - October 2010
Table of Contents 7
Reset the DNP3 Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Test the Communication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Initialize the File System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Display System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Clear the Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Read and Write Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Modbus Register for Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
DataSite Flow Configuration
Utility
(DS FloConfig)
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Hardware and Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . 107
Start DS FloConfig. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Create a New Project File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Open a Project File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Open a Recent Project File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Close DS FloConfig. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Configure PC Communication Settings . . . . . . . . . . . . . . . . . . . . . . . 112
Configure FLO Communication Settings . . . . . . . . . . . . . . . . . . . . . . 115
Open the FLO Communication Dialog Box . . . . . . . . . . . . . . . . 115
Configure Serial Port Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Configure TCP/IP Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Lower Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Set the Resource Number (Optional) . . . . . . . . . . . . . . . . . . . . . . 119
Change the Communication Password. . . . . . . . . . . . . . . . . . . . . 120
Configure FLO RTC Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Open the FLO RTC Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . 121
Read the Real-Time Clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Calibrate the Real-Time Clock (RTC). . . . . . . . . . . . . . . . . . . . . . 122
Set the Contract Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Record Flow Results for a Meter Run. . . . . . . . . . . . . . . . . . . . . . . . . 124
Display the Flow Results of a Meter Run. . . . . . . . . . . . . . . . . . . 124
Perform a Flow Calculation Test . . . . . . . . . . . . . . . . . . . . . . . . . 131
Display the Field Parameters of a Meter Run. . . . . . . . . . . . . . . . 132
Select the Measurement System . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Enable a Meter Channel and Its Accumulation Calculation . . . . 135
Set the Flow Rate Calculation Interval . . . . . . . . . . . . . . . . . . . . . 136
Select the Gas Flow Calculation Standard (AGA3/AGA7) . . . . 136
Configure AGA3 Process Parameters . . . . . . . . . . . . . . . . . . . . . 137
Configure AGA7 Process Parameters . . . . . . . . . . . . . . . . . . . . . 139
Configure Field Signal Parameters for the AGA3 Standard . . . . 140
Configure Field Signal Parameters for the AGA7 Standard . . . . 143
Select an AGA8 Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Acquire the Gas Component Parameter values . . . . . . . . . . . . . . 149