HP MPX200 Multifunction Router User Manual
Hp mpx200 multifunction router user guide
Table of contents
Document Outline
- HP MPX200 Multifunction Router User Guide
- Contents
- 1 MPX200 Multifunction Router overview
- 2 Planning the MPX200 installation
- 3 Installing the MPX200
- 4 Managing MPX200 iSCSI using HP P6000 Command View
- 5 Managing MPX200 iSCSI for 3PAR StoreServ Storage
- 6 Managing MPX200 iSCSI for XP24000/20000
- 7 MPX200 iSCSI configuration rules and guidelines
- iSCSI rules and supported maximums
- P6000 EVA storage system rules and guidelines
- HP P6000 Command View management rules and guidelines
- P6000 EVA storage system software
- 3PAR StoreServ Storage system rules and guidelines
- XP storage system rules and guidelines
- Fibre Channel switch and fabric support
- Operating system and multipath software support
- iSCSI initiator rules and guidelines
- Supported IP network adapters
- IP network requirements
- Setting up the iSCSI initiator
- Windows Server iSCSI initiator
- Multipathing
- Installing the MPIO feature for Windows Server 2012, 2008
- Installing the MPIO feature for Windows Server 2003
- Microsoft Windows Server 2003 Scalable Networking Pack
- iSCSI initiator setup for Apple Mac OS X (single-path)
- iSCSI initiator setup for Linux
- iSCSI Initiator setup for VMware
- Configuring multipath with the Solaris 10 iSCSI initiator
- Configuring Microsoft MPIO iSCSI devices
- Microsoft MPIO for iSCSI load-balancing policies
- Microsoft MPIO with QLogic iSCSI HBA
- Microsoft Windows Cluster support
- Setting up authentication
- General CHAP restrictions
- Microsoft initiator CHAP secret restrictions
- Linux CHAP restrictions
- ATTO Macintosh CHAP restrictions
- Recommended CHAP policies
- iSCSI session types
- MPX200 CHAP modes
- Enabling single-direction CHAP during discovery session and normal session
- Enabling CHAP for the MPX200-discovered iSCSI initiator entry
- Enabling CHAP for the Microsoft iSCSI initiator
- Enabling CHAP for the open-iscsi iSCSI initiator
- Enabling single-direction CHAP during discovery session and bidirectional CHAP during normal session
- Enabling bidirectional CHAP during discovery session and single-direction CHAP during normal session
- Enabling bidirectional CHAP during discovery session and bidirectional CHAP during normal session
- 8 MPX200 FCIP
- MPX200 FCIP product description
- Redundant FCIP network structure example
- Using FCIP to encapsulate FC packets
- FCIP Impact on existing iSCSI configurations
- FCIP and iSCSI performance
- MPX200 iSCSI/FCIP configurations
- IP performance tuning
- FCIP link diagnostics
- Configuring an FCIP route
- Step 1. Verify your system requirements
- Step 2. Pre-installation checklist
- Step 3. Rack-mount the MPX200
- Step 4. Install the SFPs
- Step 5. Set the MPX200 management port parameters
- Step 6. Configure the MPX200 FCIP Route parameters
- Step 7. Configure FC switch settings for the MPX200
- Step 8. Cable the MPX200 FC, GE, and management ports
- Step 9. Verify FCIP links and firmware version
- 9 MPX200 FCoE feature description
- 10 Diagnostics and troubleshooting
- MPX200 chassis diagnostics
- Issues and solutions
- HP P6000 Command View does not discover MPX200
- Initiator cannot log in to MPX200 iSCSI target
- Initiator logs in to MPX200 iSCSI target, but P6000 EVA-assigned LUNs do not appear on initiator
- P6000 EVA-presented virtual disk not seen by initiator
- Windows initiators may display Reconnecting if NIC MTU changes after connection has logged in
- Communication between HP P6000 Command View and MPX200 is down
- HP P6000 Command View issues and solutions
- 11 Support and other resources
- 12 Documentation feedback
- A Command reference
- Command syntax
- Commands
- Admin
- Beacon
- Blade
- Clear
- Date
- Exit
- Fciproute
- FRU
- Help
- History
- Image
- Initiator
- Logout
- Lunmask
- Passwd
- Ping
- Quit
- Reboot
- Reset
- Save
- Set
- Set alias
- Set CHAP
- Set chassis
- Set FC
- Set features
- Set iSCSI
- Set iSNS
- Set Mgmt
- Set NTP
- Set properties
- Set SNMP
- Set system
- Set VPGroups
- Show
- Show CHAP
- Show chassis
- Show FC
- Show fciproutes
- Show features
- Show initiators
- Show initiators LUNmask
- Show iSCSI
- Show iSNS
- Show logs
- Show LUNinfo
- Show LUNs
- Show LUNmask
- Show memory
- Show mgmt
- Show NTP
- Show perf
- Show presented targets
- Show properties
- Show SNMP
- Show stats
- Show system
- Show targets
- Show VPGroups
- Shutdown
- Target
- Traceroute
- Wanlinktest
- B Command Line Interface usage
- C Simple Network Management Protocol setup
- D Log messages
- E HP mpx100/mpx100b to MPX200 upgrade
- F Regulatory compliance and safety
- G Saving and restoring the MPX200 configuration
- Glossary
- Index