HP MPX200 Multifunction Router - Manual (Page 226)

Table 34 MPX200 log messages (continued)
FC controller failed the Get VP
Database command (for virtual port
%d
).
Error FC #%d: QLGetVpDatabase:
MBOX_CMD_GET_VP_DATABASE for VP
%d fatal error
108032
FC controller failed the Get VP
Database command (for virtual port
%d
) with status x.
Error FC #%d: QLGetVpDatabase:
MBOX_CMD_GET_VP_DATABASE for VP
%d failed %x
108033
FC controller reported failure status for
an Execute IOCB (input/output control
block) command. Error FC #%d: QLVerifyMenloFw:
EXECUTE_COMMAND_IOCB failed MB0
%x MB1 %x
108049
FC controller reported a fatal error
while processing an Execute IOCB
command. Error FC #%d: QLVerifyMenloFw:
EXECUTE_COMMAND_IOCB fatal
error
108050
FC controller reported failure status for
a Get Firmware State command. Error FC #%d: QLGetFwState: Get Firmware
State failed 0-3 %x %x %x %x
108064
Request to reset the FC processor
(adapter) received from IOCTL
interface. Info FC #%d: QLIoctlDisable: Reset
adapter
118882
FC loop initialization process (LIP)
occurred. The LIP type is reported, as Info FC #%d: QLIsrEventHandler: LIP
occurred (%x): mailbox1 = %x
119088
is the contents of the FC processor’s
mailbox 1 register.
FC LIP reset occurred. The LIP reset
type is reported, as is the contents of
the FC processor’s mailbox 1 register. Info FC #%d: QLIsrEventHandler: LIP
reset occurred (%x): mailbox1
= %x
119089
FC link up occurred. Event status is
reported, as is the contents of the FC
processor’s mailbox 1 register. Info FC #%d: QLIsrEventHandler: Link up
(%x) mailbox1 = %x
119090
FC link up occurred. Event status is
reported, as is the RunTimeMode (0 =
loop, 1 = point-to-point). Info FC #%d: QLIsrEventHandler: Link
mode up (%x): RunTimeMode=%x
119092
An RSCN was received. Event status
is reported, as is the RSCN
information. Info FC #%d: QLIsrEventHandler: RSCN
update (%x) rscnInfo: %x
119093
FC port update. Event status is
reported, as is the contents of the FC Info FC #%d: QLIsrEventHandler: Port
update (%x) mb1-3 %x %x %x
119097
processor’s mailbox 1, 2, and 3
registers.
A virtual port logged into a device,
but the device rejected the login. Info FC #%d: QLTimer: VP %d discover a
reject device PID %02x%02x%02x
119144
Update NVRAM for the invalid serial
link control for the mezzanine
platform. Info FC #%d: QLFlashGetNvram: Invalid
Serial Link Control 0x%x for
port %d
120278
For FCoE protocol, the data center
bridging exchange protocol (DCBX)
is complete. Info FC #%d: QLIsrEventHandler: DCBX
Completed (%x)
120373
For FCoE protocol, the inter-driver
communication (IDC) is complete. Info FC #%d: QLIsrEventHandler: IDC
Completion (%x) %x, %x, %x, %x,
%x, %x, %x
120374
For FCoE protocol, the IDC notification
came from another driver. Info FC #%d: QLIsrEventHandler: IDC
Notification (%x), %x, %x, %x,
%x, %x, %x, %x
120375
226 Log messages