HP MPX200 Multifunction Router - Manual (Page 223)

Table 34 MPX200 log messages (continued)
iSCSI processor reported that the iSCSI
port NVRAM contains invalid data
(checksum error). Error iSCSI #%d: QLIsrDecodeMailbox: NVRAM
invalid
74577
iSCSI processor reported a duplicate
IP address was detected (address xxxx
xxxx xxxx xxxx xxxx). Error iSCSI #%d: QLIsrDecodeMailbox: AEN
%04x, Duplicate IP address
detected, MB[1-5] %04x %04x
%04x %04x %04x
74580
iSCSI processor reported a link down
condition. Error iSCSI #%d: QLIsrDecodeMailbox: Link
down
74587
Driver failed to receive a heartbeat
from the iSCSI processor for the
specified number of seconds. Error iSCSI #%d: QLReadyTimer: Adapter
missed heartbeat for %d
seconds. Time left %d
74656
iSCSI processor (adapter) failed to
provide a heartbeat for x seconds. Error iSCSI #%d: QLReadyTimer: Adapter
missed heartbeat for 0x%x
seconds
74659
iSCSI processor failed to complete an
abort request. Error iSCSI #%d: QLReadyTimer: Abort
pTpb=%p failed, DrvCount 0x%x
74660
Driver timed out an iSCSI processor
operation and is aborting the
operation. Error iSCSI #%d: QLTimer: Abort pTpb=%p,
Type %x, Timeout 0x%x DrvCount
0x%x, DdbIndex 0x%x
74661
Driver timed out an iSCSI processor
mailbox command. Error iSCSI #%d: QLReadyTimer: MBOX_CMD
%04x %04x %04x %04x %04x %04x
%04x %04x timed out
74663
Driver timed out while attempting to
reconnect with the iSNS. Error iSCSI #%d: QLReadyTimer:
QLiSNSReenable failed.
74665
iSCSI processor was restarted. Error iSCSI #%d: QLProcessSystemError:
Restart RISC
74705
iSCSI processor rejected the firmware
initialize command. Error iSCSI #%d: QLInitializeFW:
MBOX_CMD_INITIALIZE_FIRMWARE
74746
failed %04x %04x %04x %04x %04x
%04x
Driver’s initiator database is full. The
driver is capable of storing 1024 Error iSCSI #%d: QLUpdateInitiatorData: No
more room in Initiator
Database.
74784
iSCSI initiators in its database. Use
the CLI or GUI to remove
unwanted/unused iSCSI initiators.
Driver’s target database is full. Use the
CLI or GUI to remove
unwanted/unused iSCSI targets. Error iSCSI #%d: QLSetTargetData: No more
room in Target Database.
74800
TCP retry for a frame failed on the
connection ddbIndex. Tpb contains
the frame memory address. Error iSCSI #%d: ql_process_error:
OB_TCP_IOCB_RSP_W returned
DdbInx 0x%x pTpb %p
75008
Restart iSCSI processor (RISC). Info iSCSI #%d: QLDisable: Restart RISC 86347
EEPROM updated, restart iSCSI
processor (RISC). Info iSCSI #%d: QLEnable: Restart RISC to
update EEPROM
86349
Link up reported by iSCSI processor
for GE1 or GE 2. Info iSCSI #%d: QLIsrDecodeMailbox: Link
up
86874
iSCSI controller reported a link
speed/configuration of 100 Mb
full-duplex (FDX). Info iSCSI #%d: QLGetFwStateCallback: link
100Mb FDX
87346
223