CONTREX CX-1200 - Manual (Page 403)

C - 57
(Continued)
Appendix C: Parameter Summary Numeric Quick Reference (continued)
CP-380 Cmpr1 Parm
Enter a Monitor Parameter code in Compare 1 Parameter (CP-380) that will act on the value in Cmpr1 Val (CP-388), by
using the comparison type that you entered in Cmp1 Type (CP-384). If the comparison that is established by these three
parameters is “true”, then the PLC sets the Cmpr1 Out bit (60) in the PLC to “1”, which can be used to trigger a user
defined indicator.
Minimum Value: 1 Maximum Value: 199
Default Value: 32 (VelError) Units: Parameter Code
NOTE: The following Monitor Parameters are not available for the Cmpr1 Parm (CP-380), Cmpr2 Parm (CP-381), Cmpr3
Parm (CP-382) or Cmpr4 Parm (CP-383):
MP-12 LdJobSpcVar MP-13 LdJbSzAvg MP-22 FbJobSpcVar
MP-23 FbJbSzAvg MP-41 ScaleFactor MP-42 ActScaleFactor
MP-49 Cntrl Loop MP-52 InvalidBlks MP-53 Misc Status
MP-54 Std Alarms MP-55 Custom Alms MP-56 Misc Alarms
MP-90 SerCom Char In MP-91 SerCom Errs MP-94 ROM Test
MP-95 SRAM Test MP-96 NV RAM Test MP-97 MODEL #
MP-98 RELEASE MP-99 REVISION MP-100 DI 7..0
MP-101 DI 15..8 MP-102 DO 7..0 MP-103 KeyPad Lockout
MP-108 PLC Mon 1 Val MP-109 PLC Mon 2 Val MP-110 PLC 15-8
MP-111 PLC 23-16 MP-112 PLC 31-24 MP-113 PLC 39-32
MP-114 PLC 47-40 MP-115 PLC 55-48 MP-116 PLC 63-56
MP-117 PLC 71-64 MP-118 PLC 79-72 MP-119 PLC 87-80
MP-120 PLC 95-88 MP-121 PLC 107-100 MP-122 PLC 115-108
MP-123 PLC 123-116 MP-124 PLC 131-124 MP-125 PLC 139-132
MP-126 PLC 147-140 MP-127 PLC 155-148 MP-128 PLC 163-156
MP-129 PLC 171-164 MP-130 PLC 179-172 MP-131 PLC 187-180
MP-132 PLC 195-188 MP-133 PLC 203-196 MP-134 PLC 211-204
MP-135 PLC 219-212 MP-150 Last Reset MP-151 Misc Intrpt
MP-152 Device Alms MP-153 PC at Intrpt MP-156 Mem Err Cntr
MP-157 WatchDogCntr MP-158 MiscIntrptCntr MP-168 AnlgCal Ref A
MP-169 AnlgCal Ref B MP-184 LdJSVarCnt MP-194 FbJSVarCnt
CP-381 Cmpr2 Parm
Enter a Monitor Parameter code in Compare 2 Parameter (CP-381) that will act on the value in Cmpr2 Val (CP-389), by
using the comparison type that you entered in Cmp2 Type (CP-385). If the comparison that is established by these three
parameters is “true”, then the PLC sets the Cmpr2 Out bit (61) in the PLC to “1”, which can be used to trigger a user
defined indicator.
Minimum Value: 1 Maximum Value: 199
Default Value: 33 (PosnErr) Units: Parameter Code
NOTE: Refer to the "NOTE" in CP-380.
CP-382 Cmpr3 Parm
Enter a Monitor Parameter in Compare 3 Parameter (CP-382) that will act on the value in Cmpr3 Val (CP-390), by using the
comparison type that you entered in Cmp3 Type (CP-386). If the comparison that is established by these three
parameters is “true”, then the PLC sets the Cmpr3 Out bit (62) in the PLC to “1” , which can be used to trigger a user
defined indicator.
Minimum Value: 1 Maximum Value: 199
Default Value: 37 (CO Volts) Units: Parameter Code
NOTE: Refer to the "NOTE" in CP-380.