beautypg.com

Integrated circuits, Special symbols, Transistors relay table – Elecraft K2 Owner's Manual User Manual

Page 141: Appendix b, Vco table, Diodes

background image

portion of the indicated capacitance range is actually used to cover
each Amateur band segment. VCO frequency can be calculated based on

** Based on an I.F. of 4915 kHz (e.g., 6715 - 4915 = 1800).

Relay pins 5 and 6 are not connected internally.

shown in the RESET position in schematics.

80m K2, K3

= On bottom of PC board.

30m K3, K4

15m K5, K6
12m K6, K7

160m K2

20m K4

17m K5

10m K7

Integrated Circuits

K2 Schematic Key

11915 (subtract)

14915 (subtract)
18915 (subtract)

22915 (subtract)

Special Symbols

Total Cap., pF*

6715 (subtract)

8415 (subtract)

Fixed Cap., pF

at band edge**

K13, K14, K15

K13, K14, K15

Transistors

Relay Table

16085 (add)

VCO Freq.

23085 (add)

19975 (add)

W. Burdick

Appendix B

SET Relays

VCO Table

Elecraft

E.Swartz

K14, K15

K13, K15

K13, K15

MPS5179

2SC2166
2SC1969

160m-K1

525-629

325-429

102-131

ZVN4424

PN2222A

2N7000

2N5109

1 of 1

82-111

2N3906

Diodes

Rev.

Sht.

55-84

35-64

55-84

35-64

Date

J310

Band

Band

BPF

LPF

VCO

K11
K11

K13

K15

K12

K10
K10

40m

By

K8

K9
K9

S

G

D

E

B

C

S

G

D

C

B

E

C

B

E

C

-

1Nxxxx

MV209, 1SV149

CLOCKWISE (8-PIN DIP SHOWN)

PIN 1 AND GOING COUNTER-

COUNT PINS STARTING AT

(DUAL-INLINE PACKAGE)

VOLTAGE REGULATORS

2930T-8, 78XX

PLASTIC DIP

GND

OUT

GND

OUT

GND

IN

IN

1

2
3
4

5

6

7

8

78L05, -06

Jumper

K13, K14

K12

K1

K1, 60m-K1

60m

10165 (subtract)

215-259

5250 kHz used as 60-meter lower band edge (pending U.S. FCC ruling).

K12

K14

K13, K14

NOTE: All relays are single-coil latching type and are

K1

40m

*40m ALT

11915 (subtract)

160m C75 (470)

80m C72 (270)

30m C73+C74 (67)

20m C74 (20)

17m none (0)
15m C73 (47)
12m C74 (20)

10m none (0)

D

10/23/02

C71+C73 (129)
C71+C73 (129)

* This includes capacitance of varactor diodes D23-D26 on all bands, D21-D22

C71 (120)

163-209
154-203

*40m ALT applies if D19-D20 are not installed.

***40m ALT applies if D19-D20 are not installed.

***40m ALT

+60m

+ 60 meters is available only if the K60XV option is installed.

on 80 -160 m, and D19-D20 on 40 and 60 meters (if applicable). Only a

a total inductance of 0.95 µH (T5 in parallel with L30).