Dwyer UXF2 - Manual (Page 8)

- vi -
3.6.5. Cable end treatment ··············································································································· 25
3.6.6. Connection of cable to small detector ···················································································· 26
3.6.7. Mounting of small detector on pipe························································································ 29
3.6.7.1. Mounting of detector (SX3-C0) ···························································· 29
3.6.7.2. Mounting of detector (SX3-D0) ···························································· 31
3.7. Confirmation of received signal ··························································································· 33
3.8. How to remove the sensor unit (SX3-A0/B0) ····································································· 34
3.9. Setting the range and total pulse output ··············································································· 35
3.10. How to calibrate zero ········································································································· 38
4. PARAMETERS ··························································································································· 39
4.1. Description on display/setting section·················································································· 39
4.2. Configuration of keys··········································································································· 40
4.3. Initial values of parameters ·································································································· 43
4.4. Parameter protection ············································································································ 45
4.4.1. Parameter protection ON/OFF ······························································································· 45
4.5. Output setup mode ··············································································································· 46
4.5.1. Adjusting zero point··············································································································· 46
4.5.2. Setting the damping ··············································································································· 47
4.5.3. Setting the low flow rate cutting ···························································································· 48
4.5.4. Setting the LCD indication····································································································· 49
4.5.5. Setting the flow rate and flow velocity range ········································································· 50
4.5.5.1. Setting the flow rate range (single range FLOW SPAN-1)········································· 50
4.5.5.2. Setting forward automatic 2 ranges ··········································································· 51
4.5.5.3. Setting forward/reverse automatic 2 ranges ······························································· 53
4.5.5.4. How to set analog output at error (BURNOUT) ························································ 55
4.5.6. Setting the total ······················································································································ 57
4.5.6.1. Setting the total pulse (pulse value, pulse width) ······················································· 57
4.5.6.2. Setting the preset value ····························································································· 60
4.5.6.3. TOTAL mode (total reset, start, stop) ········································································ 61
4.5.6.4. Determining how to handle the total at error (BURNOUT) ······································· 62
4.5.7. Setting the DO output ············································································································ 64
4.5.7.1. Invalidating the DO output························································································ 65
4.5.7.2. How to validate the total pulse output ······································································· 66
4.5.7.3. How to validate outputting the FLOW SPAN-2························································· 67
4.5.7.4. How to validate the alarm output··············································································· 68
4.5.7.5. How to validate the flow switch ················································································ 69
4.5.7.6. How to validate the total switch ················································································ 71
4.5.8. How to compensate the measurement value ··········································································· 73
4.6. Measure setup mode············································································································· 74
4.6.1. How to set the unit system ····································································································· 74
4.6.2. How to set the flow rate unit ·································································································· 75
4.6.3. How to set the total unit ········································································································· 76
4.6.4. How to set the piping parameters ··························································································· 77
4.7. Maintenance mode ··············································································································· 79
4.7.1. How to calibrate the analog output························································································· 79
4.7.2. How to set the constant current output ··················································································· 80
4.7.3. How to check the action of total pulses ·················································································· 81
4.7.4. How to check the status output······························································································· 82
4.7.5. How to validate the test mode (simulated flow rate output)···················································· 83
BULLETIN F-70