Yokogawa µR20000 - Manual (Page 55)

1-39
IM 04P02B01-01E
Funct
onal
Explanat
on
and
Setup
Gu
de
1.10 Functon Setup Gude
1
2
3
4
5
6
7
8
9
10
11
12
App
Index
Remote control functon (/R1 opton)
Item Descrpton Reference
Secton
Remote control function (/R1 option)
• Assign functions to the remote control input terminals 7.18
Use Remote in Basic Setting mode to set the function to be assigned to the remote
control input terminal.
• Secondary chart speed 6.9
If “chart speed switching” is assigned, use Aux > Chart 2 in Setting mode to set the
secondary chart speed.
• Switching between start printout and start printout 2 and between end printout and
end printout 2 (/BT1 option)
If BatchCMT switch is assigned
Use Batch > Dual comment in Basic Setting mode to enable or disable start
printout 2 and end printout 2.
7.24
If Use is selected, set Batch > Detal > Start2 and End2 in Setting mode. 6.14
If Not is selected, the Batch > Detal > Start2 and End2 items in Setting mode do
not appear.
Calbraton Correcton (/CC1 opton)
Item Descrpton Reference
Secton
Calibration correction function
Use Personalze > Add functon > Calbraton in Basic Setting mode and select 7.15
Use or Not.
If Use is selected,
• Use Calbraton in Basic Setting mode to set the correction mode and the number of
calibration points.
7.23
• Use Calbraton in Setting mode to set the measured value and correction value for
each channel.
6.13
If Not is selected, the Calbraton item does not appear.
Header Prntout (/BT1 opton)
Item Descrpton Reference
Secton
Setting start printout and end printout
Use Batch in Basic Setting mode to set whether to use the start printout and end
printout. If Use is selected, select a Lot No. from 4 digits, 6 digits, or OFF.
7.24
If Use is selected,
Use Batch > Batch No. in Setting mode to set the batch number. 6.14
Use Batch > Lot No. in Setting mode to set the lot number.
Use Batch > Detal > Start, End in Setting mode.
If Not is selected, the Batch > Lot No. item in Basic Setting mode and the Batch item
in Setting mode do not appear.
Switch between start printout and start printout 2 and between end printout and end printout 2 (/R1 option)
• Switch settings
Assign “BatchCMT switch” to the remote control input terminal. 7.18
Use Batch > Dual comment in Basic Setting mode to set whether to use start
printout 2 and end printout 2.
7.24
If Use is selected, set Batch > Detal > Start2 and End2 in Setting mode. 6.14
. If Not is selected, the Batch > Detal > Start2 and End2 items in Setting mode do
not appear.
• Executing the switch 1.4
The switch occurs according to the status of the “BatchCMT switch” signal when
“Record On/Off” or “Priority R_RCD” signal assigned to the remote control input
terminal rises or falls.
Printout of messages including measured/computed values
• Setting message strings 6.8
Use Aux > Message in Setting mode to enter the message to print out.
• Setting the message format
Use Batch > MSG format in Basic Setting mode and select whether to use the
message format.
7.24
If Use is selected, use Batch > MSG format > Message No. in Setting mode to set
the message format.
6.15
If Not is selected, the Batch > MSG format item does not appear.
• Executing message printout 3.10
Use Func > Message in Operation mode to execute the message printout.