5 common functions, Advanced operation, X x x – Yaskawa G5HHP Drive User Manual
Page 202
Advanced Operation
7 - 38
7.5 Common Functions
The functions that can be used for all control methods are listed in Table 7.5. Details on functions marked with
a
*
are provided in the following table.
Table 7.5 Functions Used with All Control Methods
Control Meth-
od
Group
Function
Comments
V/
f
V/
fw
/P
G
Open
-loop
Vector
Fl
ux
Ve
ct
or
b1
Sequence
Settings such as the reference input method
f f f f
b2
DC Injection Braking
* DC injection braking function settings
f f f f
b3
Speed Search
* Speed search function settings
f f f f
b4
Delay Timers
* Timer function settings
f f f f
b Application
b5
PID Control
* PID control settings
f f f f
b Application
b6
Dwell Functions
* Acceleration/deceleration time dwell function settings
f f f f
b7
Droop Control
Droop control settings
x x x
f
b8
Energy Saving
Multi-function input: Sets energy-saving control by energy saving refer-
ence.
f f
x x
b9
Zero Servo
Zero servo settings
x x x
f
C1
Accel/Decel
Acceleration/deceleration time settings
f f f f
C2
S-Curve Acc/Dec
* S-curve characteristics for acceleration/deceleration times
f f f f
C3
Motor-Slip Compensation
* Slip compensation function settings
f f f f
C Tuning
C4
Torque Compensation
* Torque compensation function settings
f f f
x
C Tuning
C5
Speed Controls
Speed control tuning
x
f
x
f
C6
Carrier Frequency
* Carrier frequency settings
f f f f
C7
Hunting Prevention
Hunting prevention settings
f f
x x
C8
Factory Tuning
Adjustment for open-loop vector control
x x
f
x
d1
Preset Reference
Frequency reference settings (when using Operator)
f f f f
d2
Reference Limits
* Frequency upper and lower limit settings
f f f f
d Reference
d3
Prohibited Frequencies
* Prohibited frequency settings
f f f f
d Reference
d4
Reference Frequence Hold
Functions
* Up/Down, Accel/Decel stop hold frequency setting
f f f f
d5
Torque Control
Torque control settings and tuning
x x x
f
E1
V/f Pattern
Motor constant settings
f f f f
E2
Motor Setup
Motor constant settings
f f f f
E Motor
E3
Motor 2 Control Methods
Control method settings for motor 2.
f f f f
E4
Motor 2 V/f Characteristics
V/f characteristics settings for motor 2.
f f f f
E5
Motor 2 Motor Constants
Motor constant setting for motor 2.
f f f f
F1
PG Speed Control Card
Settings
Constant settings for a PG Speed Control Card
x
f
x
f
F2
Analog Reference Card AI
*
User constant settings for an Analog Reference Card
f f f f
F3
Digital Reference Card DI
*
User constant settings for a Digital Reference Card
f f f f
F4
Analog Monitor Card AO
*
User constant settings for an Analog Monitor Card
f f f f
F Options
F5
Digital Output Card DO
User constant settings for a Digital Output Card
f f f f
F Options
F6
Digital Output Card DO
User constant settings for a Digital Output Card
f f f f
F7
Pulse Monitor Card PO
*
User constant settings for a Pulse Monitor Card
f f f f
F8
SI-F/SI-G Transmission
Card
User constant settings for a Transmission Card
f f f f
F9
CP-916B Transmission
Card
User constant settings for a Transmission Card
f f f f
7