Comtech EF Data CDM-600/600L - Manual (Page 54)

CDM-600/600L Open Network Satellite Modem Revision 3
Introduction MN/CDM600L.IOM
1–26
1.5.4 Automatic Uplink Power Control (AUPC)
Operating Mode Requires Closed Network Framed mode for transport of Eb/No information from remote modem
(EDMAC can be enabled or disabled)
Target Eb/No range 0 to 14.9 dB at remote demod (default is 4.0 dB)
Max AUPC range 0 to 9 dB (default is 3 dB)
Monitor functions Remote demod Eb/No and Tx power level increase (front panel or via remote control interface)
1.5.5 Data Rate Ranges
Code Rate/Modulation FEC Type Data Rate Range Comments
Uncoded BPSK None 4.8 kbps to 10.0 Mbps
Uncoded QPSK/OQPSK None 9.6 kbps to 20 Mbps
Rate 1/2 BPSK Viterbi 2.4 kbps to 5.0 Mbps
Rate 1/2 BPSK Sequential 2.4 kbps to 1.024 Mbps
Rate 1/2 BPSK Viterbi with R-S 2.4 kbps to 4.444 Mbps
Rate 1/2 BPSK Sequential with R-S 2.4 kbps to 1.024 Mbps
Rate 1/2 QPSK/OQPSK Viterbi 4.8 kbps to 10.0 Mbps
Rate 1/2 QPSK/OQPSK Sequential 4.8 kbps to 2.048 Mbps
Rate 1/2 QPSK/OQPSK Viterbi with R-S 4.8 kbps to 8.888 Mbps
Rate 1/2 QPSK/OQPSK Sequential with R-S 4.8 kbps to 2.048 Mbps
Rate 3/4 QPSK/OQPSK Viterbi 7.2 kbps to 15 Mbps
Rate 3/4 QPSK/OQPSK Sequential 7.2 kbps to 2.048 Mbps
Rate 3/4 QPSK/OQPSK Viterbi with R-S 7.2 kbps to 13.333 Mbps
Rate 3/4 QPSK/OQPSK Sequential with R-S 7.2 kbps to 2.048 Mbps
Rate 7/8 QPSK/OQPSK Viterbi 8.4 kbps to 17.5 Mbps
Rate 7/8 QPSK/OQPSK Sequential 8.4 kbps to 2.048 Mbps
Rate 7/8 QPSK/OQPSK Viterbi with R-S 8.4 kbps to 15.555 Mbps
Rate 7/8 QPSK/OQPSK Sequential with R-S 8.4 kbps to 2.048 Mbps
Rate 2/3 8-PSK TCM 9.6 kbps to 20.0 Mbps
Rate 2/3 8-PSK TCM with R-S 9.6 kbps to 17.777 Mbps
Rate 3/4 16-QAM Viterbi with R-S 14.4 kbps to 20.0 Mbps
Rate 7/8 16-QAM Viterbi with R-S 16.8 kbps to 20.0 Mbps
Rate 21/44 BPSK TPC 4.8 kbps to 3.2 Mbps To 4.77 Mbps with High Rate Turbo card
Rate 5/16 BPSK TPC 4.8 kbps to 2.048 Mbps To 3.12 Mbps with High Rate Turbo card
Rate 3/4 QPSK/OQPSK TPC 7.2 kbps to 5.0 Mbps To 15 Mbps with High Rate Turbo card
Rate 3/4 8-PSK TPC 10.8 kbps to 5.0 Mbps To 20 Mbps with High Rate Turbo card
Rate 3/4 16-QAM TPC 14.4 kbps to 5.0 Mbps To 20 Mbps with High Rate Turbo card
Rate 1/2 QPSK/OQPSK TPC 4.8 kbps to 9.54 Mbps
High Rate Turbo card only
Rate 7/8 QPSK/OQPSK TPC 8.4 kbps to 17.5 Mbps
Rate 0.95 QPSK/OQPSK TPC 9.1 kbps to 18.888 Mbps
Rate 7/8 8-PSK TPC 12.6 kbps to 20 Mbps
Rate 0.95 8-PSK TPC 13.6 kbps to 20 Mbps
Rate 7/8 16-QAM TPC 16.8 kbps to 20 Mbps
Rate 1/2 BPSK LDPC 2.4 kbps to 5.0 Mbps
CDM-600L: TPC/LDPC codec only
Rate 1/2 QPSK/OQPSK LDPC 4.8 kbps to 10.0 Mbps
Rate 2/3 QPSK/OQPSK LDPC 6.4 kbps to 13.333 Mbps
Rate 3/4 QPSK/OQPSK LDPC 7.2 kbps to 15.0 Mbps
Rate 2/3 8-PSK/8-QAM LDPC 9.6 kbps to 19.0 Mbps
Rate 3/4 8-PSK/8-QAM LDPC 10.8 kbps to 20.0 Mbps
Rate 3/4 16-QAM LDPC 14.4 kbps to 20.0 Mbps
Important Notes :
1. If EDMAC framing is employed, the upper data rate will be reduced by 5% for data rates up to 2.048 Mbps, and by 1.58% for
data rates above 2.048 Mbps)
2. If ESC++ framing is employed, the upper data rate will be reduced 1.58%.