Basler Electric DGC-2020HD Modbus Protocol - Manual (Page 27)

9469300991 Rev A 21
DGC-2020HD Modbus ™ Protocol Default Register Table
Name Description Group Register Type Bytes R/W Unit Range
CEM 4 Contact Input 9 Contact Recognition GG 0744 Uint32 4 R W n/a Always=0
Engine Running=1
CEM 4 Contact Input 9 Alarm Configuration GG 0746 Uint32 4 R W n/a Status Only=0
Pre-Alarm=1
Alarm=2
CEM 4 Contact Input 9 Activation Delay GG 0748 Uint32 4 R W Second 0 - 300
CEM 4 Contact Input
10 Contact Recognition GG 0750 Uint32 4 R W n/a Always=0
Engine Running=1
CEM 4 Contact Input
10
Alarm Configuration GG 0752 Uint32 4 R W n/a Status Only=0
Pre-Alarm=1
Alarm=2
CEM 4 Contact Input
10 Activation Delay GG 0754 Uint32 4 R W Second 0 - 300
Auto Config Detect Enable GG 0756 Uint32 4 R W n/a Disabled=0
Enabled=1
Auto Config Detect Single-Phase Detection Threshold GG 0758 Float 4 R W Volt 0 - 480
Auto Config Detect Single-Phase Detection Gen Connection GG 0760 Uint32 4 R W n/a AB=0
AC=1
Auto Config Detect Low-Line Detection Threshold GG 0762 Float 4 R W Volt 0 - 480
Binary Points
Name Description Register Bit Type Bytes R/W Range
Scale Factor Override Alternate Frequency Override 1000 0 Uint16 2 R False=0 True=1
Reserved 1000 1
System Data Logic 0 1000 2 Uint16 2 R False=0 True=1
System Data Logic 1 1000 3 Uint16 2 R False=0 True=1
Alarms Real-Time Clock Alarm 1000 4 Uint16 2 R False=0 True=1
Alarms Date/Time Set Alarm 1000 5 Uint16 2 R False=0 True=1
Alarms Firmware Change Alarm 1000 6 Uint16 2 R False=0 True=1
Alarms Frequency Out-of-Range Alarm 1000 7 Uint16 2 R False=0 True=1
Alarms Ethernet Link 1 Lost Alarm 1000 8 Uint16 2 R False=0 True=1
Alarms Ethernet Link 2 Lost Alarm 1000 9 Uint16 2 R False=0 True=1
Alarms USB COM Alarm 1000 10 Uint16 2 R False=0 True=1
Alarms IRIG Sync Lost Alarm 1000 11 Uint16 2 R False=0 True=1
Alarms Logic = None Alarm 1000 12 Uint16 2 R False=0 True=1
Alarms No User Setting Alarm 1000 13 Uint16 2 R False=0 True=1
Alarms NTP Sync Lost Alarm 1000 14 Uint16 2 R False=0 True=1
Alarms uP Reset Alarm 1000 15 Uint16 2 R False=0 True=1
Alarms Programmable Alarm 1 1001 0 Uint16 2 R False=0 True=1
Alarms Programmable Alarm 2 1001 1 Uint16 2 R False=0 True=1
Alarms Programmable Alarm 3 1001 2 Uint16 2 R False=0 True=1
Alarms Programmable Alarm 4 1001 3 Uint16 2 R False=0 True=1
Alarms Programmable Alarm 5 1001 4 Uint16 2 R False=0 True=1
Alarms Programmable Alarm 6 1001 5 Uint16 2 R False=0 True=1
Alarms Programmable Alarm 7 1001 6 Uint16 2 R False=0 True=1
Alarms Programmable Alarm 8 1001 7 Uint16 2 R False=0 True=1
Alarms Programmable Alarm 9 1001 8 Uint16 2 R False=0 True=1
Alarms Programmable Alarm 10 1001 9 Uint16 2 R False=0 True=1
Alarms Programmable Alarm 11 1001 10 Uint16 2 R False=0 True=1
Alarms Programmable Alarm 12 1001 11 Uint16 2 R False=0 True=1
Alarms Programmable Alarm 13 1001 12 Uint16 2 R False=0 True=1
Alarms Programmable Alarm 14 1001 13 Uint16 2 R False=0 True=1
Alarms Programmable Alarm 15 1001 14 Uint16 2 R False=0 True=1
Alarms Programmable Alarm 16 1001 15 Uint16 2 R False=0 True=1
Alarms Unsupported Number of AEMs 1002 0 Uint16 2 R False=0 True=1
Alarms Unsupported Number of CEMs 1002 1 Uint16 2 R False=0 True=1
Alarms Logic Alarm 1002 2 Uint16 2 R False=0 True=1
Alarms Logic Pre-Alarm 1002 3 Uint16 2 R False=0 True=1
Alarms Global Sender Fail Alarm 1002 4 Uint16 2 R False=0 True=1
Alarms Clock Not Set Alarm 1002 5 Uint16 2 R False=0 True=1
Alarms Clock Battery Low Alarm 1002 6 Uint16 2 R False=0 True=1
Alarm Report Alarm Output 1002 7 Uint16 2 R False=0 True=1
Pre-Alarm Report Alarm Output 1002 8 Uint16 2 R False=0 True=1
Contact Outputs Output 1 1002 9 Uint16 2 R False=0 True=1
Contact Outputs Output 2 1002 10 Uint16 2 R False=0 True=1
Contact Outputs Output 3 1002 11 Uint16 2 R False=0 True=1
Contact Outputs Output 4 1002 12 Uint16 2 R False=0 True=1
Contact Outputs Output 5 1002 13 Uint16 2 R False=0 True=1
Contact Outputs Output 6 1002 14 Uint16 2 R False=0 True=1
Contact Outputs Output 7 1002 15 Uint16 2 R False=0 True=1
Contact Outputs Output 8 1003 0 Uint16 2 R False=0 True=1
Contact Outputs Output 9 1003 1 Uint16 2 R False=0 True=1
Contact Outputs Output 10 1003 2 Uint16 2 R False=0 True=1