Rockwell Automation 1404-M4_M5_M6_M8 Powermonitor 3000 User Manual, Firmware rev. 3.0 or LATER User Manual
Page 189
Publication 1404-UM001F-EN-P - November 2009
189
Powermonitor 3000 Data Tables Appendix A
Oscillograph Results Parameters
R
•
N40
61
48
-
29 or 59
(14)
• •
Load Factor Log Configuration/Read-back Select
Parameters
R/W
N41
16
49,50
-
6
• •
Load Factor Log Results Parameters
R
•
F42
43
51
-
14
• •
Transient Analysis Configuration/Read-back Select
Parameters
R/W
F43
44
52,53
-
13
•
Transient Analysis Metering Results Parameters
R
•
F44
32
54
-
14
•
Transient Capture Clear/Read-back Data Select
Parameters
R/W
N45
17
55,56
-
13
•
Transient Capture Results Parameters
R
•
N46
60
57
-
29 or 59
(14)
•
Advanced Metering Configuration Parameters
R/W
N47
19
58,59
-
10
•
Harmonic Results; Odd Harmonics 43…63
Parameters
R
•
F48
45
60
-
14
•
Harmonic Results; Even Harmonics 42…62
Parameters
R
•
F49
46
61
-
14
•
Catalog Number and WIN Parameters
R
N51
50
64
32301
29
• • •
Network Demand Sync and Time Configuration
Parameters
(2)
R/W
N52
-
65, 66
41901
20
• • •
(2)
W
N53
-
67
42001
1
• • •
Daylight Saving Time Configuration Parameters
R/W
N54
47
68,69
42101
10
• • •
Time of Use Register Configuration Parameters
R/W
N55
49
70,71
42201
10
• • •
Time of Use Records – Real Energy and Demand
Parameters
R
F56
51
72
32401
12
• • •
Time of Use Records – Reactive Energy and
Demand Parameters
R
F57
52
73
32501
12
• • •
Time of Use Records – Apparent Energy and
Demand Parameters
R
F58
53
74
32601
12
• • •
Single Password Write Parameters
R/W
N60
-
75,76
42701
1
• • •
Single Parameter Read Parameters
R
-
-
80…
103
-
1
• • •
(1)
Event log user comment feature has been removed from master firmware revision 3.1 and later.
(2)
Supported only on 1404-xxxxx-ENT-xx.
(3)
Data is most commonly read from this table by using the Indexed read method.
(4)
Powermonitor 3000 unit starts with file 9 to avoid any data-type incompatibility with SLC file numbers 1…8, which are of a fixed data type.
(5)
This is a reply to a PCCC diagnostic status request, used by RSWho to display text and an icon for the product.
(6)
Listed Modbus address is one-based. For zero-based addressing, subtract a value of one (1) from the listed address.
(7)
The default size is 2 input words and 2 output words for remote I/O. The input table (instance 1) default size is 6 words and is user configurable for DeviceNet, EtherNet/IP,
and ControlNet networks. Remote I/O tables and the default DeviceNet input channel are PLC/SLC controllers compatible, but if you reconfigure the DeviceNet input
channel (Instance 1), it may or may not be PLC/SLC controllers compatible (depending on the number of parameters configured).
(8)
Basic device configuration data table size is 8 elements for the M4 and M5, and 9 elements for the M6 and M8.
(9)
Table size increased in revision 3.1x of the master module firmware.
(10)
The size of the Trend log results table is 28 elements for the DeviceNet network and 44 elements for all other communication protocols.
(11)
The size of the Event log results table is 14 elements for M4/M5, 17 elements for M6 and 18 elements for the M8.
Summary of Powermonitor 3000 Data Tables for all Communication Options
Data Table Name and Description
(1)
Dat
a
Access
Indexed
Reads
(3
)
File No.
(4)
(DF
1, CSP)
Remote I/
O
BT Siz
e
As
sy
Insta
nce
(CIP
, D
N
et)
Mod
bus
Starting
Address
(6)
No. of
Elements
Applies to
Configur
-
able
Refer to
Page
M4, M
5
M6
M8